/*
- * Copyright 2008 Freescale Semiconductor.
+ * Copyright 2008-2012 Freescale Semiconductor, Inc.
*
* See file CREDITS for list of people who contributed to this
* project.
#include <asm/fsl_pci.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/io.h>
+#include <asm/fsl_serdes.h>
#include <spd.h>
#include <miiphy.h>
#include <libfdt.h>
#include <spd_sdram.h>
#include <fdt_support.h>
+#include <fsl_mdio.h>
#include <tsec.h>
#include <netdev.h>
#include <sata.h>
-#include "../common/pixis.h"
#include "../common/sgmii_riser.h"
-phys_size_t fixed_sdram(void);
-
int board_early_init_f (void)
{
#ifdef CONFIG_MMC
volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
setbits_be32(&gur->pmuxcr,
- (MPC85xx_PMUXCR_SD_DATA |
- MPC85xx_PMUXCR_SDHC_CD |
+ (MPC85xx_PMUXCR_SDHC_CD |
MPC85xx_PMUXCR_SDHC_WP));
+ /* The MPC8536DS board insert the SDHC_WP pin for erratum NMG_eSDHC118,
+ * however, this erratum only applies to MPC8536 Rev1.0.
+ * So set SDHC_WP to active-low when use MPC8536 Rev1.1 and greater.*/
+ if ((((SVR_MAJ(get_svr()) & 0x7) == 0x1) &&
+ (SVR_MIN(get_svr()) >= 0x1))
+ || (SVR_MAJ(get_svr() & 0x7) > 0x1))
+ setbits_be32(&gur->gencfgr, MPC85xx_GENCFGR_SDHC_WP_INV);
#endif
return 0;
}
int checkboard (void)
{
- printf ("Board: MPC8536DS, System ID: 0x%02x, "
- "System Version: 0x%02x, FPGA Version: 0x%02x\n",
- in8(PIXIS_BASE + PIXIS_ID), in8(PIXIS_BASE + PIXIS_VER),
- in8(PIXIS_BASE + PIXIS_PVER));
- return 0;
-}
-
-phys_size_t
-initdram(int board_type)
-{
- phys_size_t dram_size = 0;
-
- puts("Initializing....");
-
-#ifdef CONFIG_SPD_EEPROM
- dram_size = fsl_ddr_sdram();
-#else
- dram_size = fixed_sdram();
-#endif
- dram_size = setup_ddr_tlbs(dram_size / 0x100000);
- dram_size *= 0x100000;
+ u8 vboot;
+ u8 *pixis_base = (u8 *)PIXIS_BASE;
+
+ printf("Board: MPC8536DS Sys ID: 0x%02x, "
+ "Sys Ver: 0x%02x, FPGA Ver: 0x%02x, ",
+ in_8(pixis_base + PIXIS_ID), in_8(pixis_base + PIXIS_VER),
+ in_8(pixis_base + PIXIS_PVER));
+
+ vboot = in_8(pixis_base + PIXIS_VBOOT);
+ switch ((vboot & PIXIS_VBOOT_LBMAP) >> 5) {
+ case PIXIS_VBOOT_LBMAP_NOR0:
+ puts ("vBank: 0\n");
+ break;
+ case PIXIS_VBOOT_LBMAP_NOR1:
+ puts ("vBank: 1\n");
+ break;
+ case PIXIS_VBOOT_LBMAP_NOR2:
+ puts ("vBank: 2\n");
+ break;
+ case PIXIS_VBOOT_LBMAP_NOR3:
+ puts ("vBank: 3\n");
+ break;
+ case PIXIS_VBOOT_LBMAP_PJET:
+ puts ("Promjet\n");
+ break;
+ case PIXIS_VBOOT_LBMAP_NAND:
+ puts ("NAND\n");
+ break;
+ }
- puts(" DDR: ");
- return dram_size;
+ return 0;
}
#if !defined(CONFIG_SPD_EEPROM)
static struct pci_controller pci1_hose;
#endif
-#ifdef CONFIG_PCIE1
-static struct pci_controller pcie1_hose;
-#endif
-
-#ifdef CONFIG_PCIE2
-static struct pci_controller pcie2_hose;
-#endif
-
-#ifdef CONFIG_PCIE3
-static struct pci_controller pcie3_hose;
-#endif
-
-int first_free_busno=0;
-
-void
-pci_init_board(void)
+#ifdef CONFIG_PCI
+void pci_init_board(void)
{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- uint devdisr = gur->devdisr;
- uint sdrs2_io_sel =
- (gur->pordevsr & MPC85xx_PORDEVSR_SRDS2_IO_SEL) >> 27;
- uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
- uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
-
- debug(" pci_init_board: devdisr=%x, sdrs2_io_sel=%x, io_sel=%x,\
- host_agent=%x\n", devdisr, sdrs2_io_sel, io_sel, host_agent);
-
- if (sdrs2_io_sel == 7)
- printf(" Serdes2 disalbed\n");
- else if (sdrs2_io_sel == 4) {
- printf(" eTSEC1 is in sgmii mode.\n");
- printf(" eTSEC3 is in sgmii mode.\n");
- } else if (sdrs2_io_sel == 6)
- printf(" eTSEC1 is in sgmii mode.\n");
-
-#ifdef CONFIG_PCIE3
-{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR;
- struct pci_controller *hose = &pcie3_hose;
- int pcie_ep = (host_agent == 1);
- int pcie_configured = (io_sel == 7);
- struct pci_region *r = hose->regions;
-
- if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
- printf ("\n PCIE3 connected to Slot3 as %s (base address %x)",
- pcie_ep ? "End Point" : "Root Complex",
- (uint)pci);
- if (pci->pme_msg_det) {
- pci->pme_msg_det = 0xffffffff;
- debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
- }
- printf ("\n");
-
- /* inbound */
- r += fsl_pci_setup_inbound_windows(r);
-
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE3_MEM_BUS,
- CONFIG_SYS_PCIE3_MEM_PHYS,
- CONFIG_SYS_PCIE3_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* outbound io */
- pci_set_region(r++,
- CONFIG_SYS_PCIE3_IO_BUS,
- CONFIG_SYS_PCIE3_IO_PHYS,
- CONFIG_SYS_PCIE3_IO_SIZE,
- PCI_REGION_IO);
-
- hose->region_count = r - hose->regions;
-
- hose->first_busno=first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
-
- first_free_busno=hose->last_busno+1;
- printf (" PCIE3 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
- } else {
- printf (" PCIE3: disabled\n");
- }
-
- }
-#else
- gur->devdisr |= MPC85xx_DEVDISR_PCIE3; /* disable */
-#endif
-
-#ifdef CONFIG_PCIE1
- {
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
- struct pci_controller *hose = &pcie1_hose;
- int pcie_ep = (host_agent == 5);
- int pcie_configured = (io_sel == 2 || io_sel == 3
- || io_sel == 5 || io_sel == 7);
- struct pci_region *r = hose->regions;
-
- if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
- printf ("\n PCIE1 connected to Slot1 as %s (base address %x)",
- pcie_ep ? "End Point" : "Root Complex",
- (uint)pci);
- if (pci->pme_msg_det) {
- pci->pme_msg_det = 0xffffffff;
- debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
- }
- printf ("\n");
-
- /* inbound */
- r += fsl_pci_setup_inbound_windows(r);
-
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE1_MEM_BUS,
- CONFIG_SYS_PCIE1_MEM_PHYS,
- CONFIG_SYS_PCIE1_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* outbound io */
- pci_set_region(r++,
- CONFIG_SYS_PCIE1_IO_BUS,
- CONFIG_SYS_PCIE1_IO_PHYS,
- CONFIG_SYS_PCIE1_IO_SIZE,
- PCI_REGION_IO);
-
-#ifdef CONFIG_SYS_PCIE1_MEM_BUS2
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE1_MEM_BUS2,
- CONFIG_SYS_PCIE1_MEM_PHYS2,
- CONFIG_SYS_PCIE1_MEM_SIZE2,
- PCI_REGION_MEM);
-#endif
- hose->region_count = r - hose->regions;
- hose->first_busno=first_free_busno;
-
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
-
- first_free_busno=hose->last_busno+1;
- printf(" PCIE1 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
-
- } else {
- printf (" PCIE1: disabled\n");
- }
-
- }
-#else
- gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
-#endif
-
-#ifdef CONFIG_PCIE2
- {
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
- struct pci_controller *hose = &pcie2_hose;
- int pcie_ep = (host_agent == 3);
- int pcie_configured = (io_sel == 5 || io_sel == 7);
- struct pci_region *r = hose->regions;
-
- if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
- printf ("\n PCIE2 connected to Slot 2 as %s (base address %x)",
- pcie_ep ? "End Point" : "Root Complex",
- (uint)pci);
- if (pci->pme_msg_det) {
- pci->pme_msg_det = 0xffffffff;
- debug (" with errors. Clearing. Now 0x%08x",pci->pme_msg_det);
- }
- printf ("\n");
-
- /* inbound */
- r += fsl_pci_setup_inbound_windows(r);
-
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE2_MEM_BUS,
- CONFIG_SYS_PCIE2_MEM_PHYS,
- CONFIG_SYS_PCIE2_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* outbound io */
- pci_set_region(r++,
- CONFIG_SYS_PCIE2_IO_BUS,
- CONFIG_SYS_PCIE2_IO_PHYS,
- CONFIG_SYS_PCIE2_IO_SIZE,
- PCI_REGION_IO);
-
-#ifdef CONFIG_SYS_PCIE2_MEM_BUS2
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCIE2_MEM_BUS2,
- CONFIG_SYS_PCIE2_MEM_PHYS2,
- CONFIG_SYS_PCIE2_MEM_SIZE2,
- PCI_REGION_MEM);
-#endif
- hose->region_count = r - hose->regions;
- hose->first_busno=first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
- first_free_busno=hose->last_busno+1;
- printf (" PCIE2 on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
-
- } else {
- printf (" PCIE2: disabled\n");
- }
-
- }
-#else
- gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
-#endif
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ struct fsl_pci_info pci_info;
+ u32 devdisr, pordevsr;
+ u32 porpllsr, pci_agent, pci_speed, pci_32, pci_arb, pci_clk_sel;
+ int first_free_busno;
+ first_free_busno = fsl_pcie_init_board(0);
#ifdef CONFIG_PCI1
-{
- volatile ccsr_fsl_pci_t *pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCI1_ADDR;
- struct pci_controller *hose = &pci1_hose;
- struct pci_region *r = hose->regions;
-
- uint pci_agent = (host_agent == 6);
- uint pci_speed = 66666000; /*get_clock_freq (); PCI PSPEED in [4:5] */
- uint pci_32 = 1;
- uint pci_arb = gur->pordevsr & MPC85xx_PORDEVSR_PCI1_ARB; /* PORDEVSR[14] */
- uint pci_clk_sel = gur->porpllsr & MPC85xx_PORDEVSR_PCI1_SPD; /* PORPLLSR[16] */
+ devdisr = in_be32(&gur->devdisr);
+ pordevsr = in_be32(&gur->pordevsr);
+ porpllsr = in_be32(&gur->porpllsr);
+ pci_speed = 66666000;
+ pci_32 = 1;
+ pci_arb = pordevsr & MPC85xx_PORDEVSR_PCI1_ARB;
+ pci_clk_sel = porpllsr & MPC85xx_PORDEVSR_PCI1_SPD;
if (!(devdisr & MPC85xx_DEVDISR_PCI1)) {
- printf ("\n PCI: %d bit, %s MHz, %s, %s, %s (base address %x)\n",
+ SET_STD_PCI_INFO(pci_info, 1);
+ set_next_law(pci_info.mem_phys,
+ law_size_bits(pci_info.mem_size), pci_info.law);
+ set_next_law(pci_info.io_phys,
+ law_size_bits(pci_info.io_size), pci_info.law);
+
+ pci_agent = fsl_setup_hose(&pci1_hose, pci_info.regs);
+ printf("PCI: %d bit, %s MHz, %s, %s, %s (base address %lx)\n",
(pci_32) ? 32 : 64,
(pci_speed == 33333000) ? "33" :
(pci_speed == 66666000) ? "66" : "unknown",
pci_clk_sel ? "sync" : "async",
pci_agent ? "agent" : "host",
pci_arb ? "arbiter" : "external-arbiter",
- (uint)pci
- );
-
- /* inbound */
- r += fsl_pci_setup_inbound_windows(r);
-
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCI1_MEM_BUS,
- CONFIG_SYS_PCI1_MEM_PHYS,
- CONFIG_SYS_PCI1_MEM_SIZE,
- PCI_REGION_MEM);
-
- /* outbound io */
- pci_set_region(r++,
- CONFIG_SYS_PCI1_IO_BUS,
- CONFIG_SYS_PCI1_IO_PHYS,
- CONFIG_SYS_PCI1_IO_SIZE,
- PCI_REGION_IO);
-
-#ifdef CONFIG_SYS_PCI1_MEM_BUS2
- /* outbound memory */
- pci_set_region(r++,
- CONFIG_SYS_PCI1_MEM_BUS2,
- CONFIG_SYS_PCI1_MEM_PHYS2,
- CONFIG_SYS_PCI1_MEM_SIZE2,
- PCI_REGION_MEM);
-#endif
- hose->region_count = r - hose->regions;
- hose->first_busno=first_free_busno;
- pci_setup_indirect(hose, (int) &pci->cfg_addr, (int) &pci->cfg_data);
-
- fsl_pci_init(hose);
- first_free_busno=hose->last_busno+1;
- printf ("PCI on bus %02x - %02x\n",
- hose->first_busno,hose->last_busno);
+ pci_info.regs);
+
+ first_free_busno = fsl_pci_init_port(&pci_info,
+ &pci1_hose, first_free_busno);
} else {
- printf (" PCI: disabled\n");
+ printf("PCI: disabled\n");
}
-}
+
+ puts("\n");
#else
- gur->devdisr |= MPC85xx_DEVDISR_PCI1; /* disable */
+ setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCI1); /* disable */
#endif
}
-
+#endif
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
- const u8 flash_esel = 1;
+ const u8 flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
return 0;
}
-#ifdef CONFIG_GET_CLK_FROM_ICS307
-/* decode S[0-2] to Output Divider (OD) */
-static unsigned char
-ics307_S_to_OD[] = {
- 10, 2, 8, 4, 5, 7, 3, 6
-};
-
-/* Calculate frequency being generated by ICS307-02 clock chip based upon
- * the control bytes being programmed into it. */
-/* XXX: This function should probably go into a common library */
-static unsigned long
-ics307_clk_freq (unsigned char cw0, unsigned char cw1, unsigned char cw2)
-{
- const unsigned long long InputFrequency = CONFIG_ICS307_REFCLK_HZ;
- unsigned long VDW = ((cw1 << 1) & 0x1FE) + ((cw2 >> 7) & 1);
- unsigned long RDW = cw2 & 0x7F;
- unsigned long OD = ics307_S_to_OD[cw0 & 0x7];
- unsigned long freq;
-
- /* CLK1Frequency = InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD) */
-
- /* cw0: C1 C0 TTL F1 F0 S2 S1 S0
- * cw1: V8 V7 V6 V5 V4 V3 V2 V1
- * cw2: V0 R6 R5 R4 R3 R2 R1 R0
- *
- * R6:R0 = Reference Divider Word (RDW)
- * V8:V0 = VCO Divider Word (VDW)
- * S2:S0 = Output Divider Select (OD)
- * F1:F0 = Function of CLK2 Output
- * TTL = duty cycle
- * C1:C0 = internal load capacitance for cyrstal
- */
-
- /* Adding 1 to get a "nicely" rounded number, but this needs
- * more tweaking to get a "properly" rounded number. */
-
- freq = 1 + (InputFrequency * 2 * (VDW + 8) / ((RDW + 2) * OD));
-
- debug("ICS307: CW[0-2]: %02X %02X %02X => %u Hz\n", cw0, cw1, cw2,
- freq);
- return freq;
-}
-
-unsigned long
-get_board_sys_clk(ulong dummy)
-{
- return ics307_clk_freq (
- in8(PIXIS_BASE + PIXIS_VSYSCLK0),
- in8(PIXIS_BASE + PIXIS_VSYSCLK1),
- in8(PIXIS_BASE + PIXIS_VSYSCLK2)
- );
-}
-
-unsigned long
-get_board_ddr_clk(ulong dummy)
-{
- return ics307_clk_freq (
- in8(PIXIS_BASE + PIXIS_VDDRCLK0),
- in8(PIXIS_BASE + PIXIS_VDDRCLK1),
- in8(PIXIS_BASE + PIXIS_VDDRCLK2)
- );
-}
-#else
-unsigned long
-get_board_sys_clk(ulong dummy)
-{
- u8 i;
- ulong val = 0;
-
- i = in8(PIXIS_BASE + PIXIS_SPD);
- i &= 0x07;
-
- switch (i) {
- case 0:
- val = 33333333;
- break;
- case 1:
- val = 40000000;
- break;
- case 2:
- val = 50000000;
- break;
- case 3:
- val = 66666666;
- break;
- case 4:
- val = 83333333;
- break;
- case 5:
- val = 100000000;
- break;
- case 6:
- val = 133333333;
- break;
- case 7:
- val = 166666666;
- break;
- }
-
- return val;
-}
-
-unsigned long
-get_board_ddr_clk(ulong dummy)
-{
- u8 i;
- ulong val = 0;
-
- i = in8(PIXIS_BASE + PIXIS_SPD);
- i &= 0x38;
- i >>= 3;
-
- switch (i) {
- case 0:
- val = 33333333;
- break;
- case 1:
- val = 40000000;
- break;
- case 2:
- val = 50000000;
- break;
- case 3:
- val = 66666666;
- break;
- case 4:
- val = 83333333;
- break;
- case 5:
- val = 100000000;
- break;
- case 6:
- val = 133333333;
- break;
- case 7:
- val = 166666666;
- break;
- }
- return val;
-}
-#endif
-
-int sata_initialize(void)
-{
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
- uint sdrs2_io_sel =
- (gur->pordevsr & MPC85xx_PORDEVSR_SRDS2_IO_SEL) >> 27;
- if (sdrs2_io_sel & 0x04)
- return 1;
-
- return __sata_initialize();
-}
-
int board_eth_init(bd_t *bis)
{
#ifdef CONFIG_TSEC_ENET
+ struct fsl_pq_mdio_info mdio_info;
struct tsec_info_struct tsec_info[2];
- volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
int num = 0;
- uint sdrs2_io_sel =
- (gur->pordevsr & MPC85xx_PORDEVSR_SRDS2_IO_SEL) >> 27;
#ifdef CONFIG_TSEC1
SET_STD_TSEC_INFO(tsec_info[num], 1);
- if ((sdrs2_io_sel == 4) || (sdrs2_io_sel == 6)) {
+ if (is_serdes_configured(SGMII_TSEC1)) {
+ puts("eTSEC1 is in sgmii mode.\n");
tsec_info[num].phyaddr = 0;
tsec_info[num].flags |= TSEC_SGMII;
}
#endif
#ifdef CONFIG_TSEC3
SET_STD_TSEC_INFO(tsec_info[num], 3);
- if (sdrs2_io_sel == 4) {
+ if (is_serdes_configured(SGMII_TSEC3)) {
+ puts("eTSEC3 is in sgmii mode.\n");
tsec_info[num].phyaddr = 1;
tsec_info[num].flags |= TSEC_SGMII;
}
}
#ifdef CONFIG_FSL_SGMII_RISER
- if ((sdrs2_io_sel == 4) || (sdrs2_io_sel == 6))
+ if (is_serdes_configured(SGMII_TSEC1) ||
+ is_serdes_configured(SGMII_TSEC3)) {
fsl_sgmii_riser_init(tsec_info, num);
+ }
#endif
+ mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
+ mdio_info.name = DEFAULT_MII_NAME;
+ fsl_pq_mdio_init(bis, &mdio_info);
+
tsec_eth_init(bis, tsec_info, num);
#endif
return pci_eth_init(bis);
{
ft_cpu_setup(blob, bd);
-#ifdef CONFIG_PCI1
- ft_fsl_pci_setup(blob, "pci0", &pci1_hose);
-#endif
-#ifdef CONFIG_PCIE2
- ft_fsl_pci_setup(blob, "pci1", &pcie2_hose);
-#endif
-#ifdef CONFIG_PCIE2
- ft_fsl_pci_setup(blob, "pci2", &pcie1_hose);
-#endif
-#ifdef CONFIG_PCIE1
- ft_fsl_pci_setup(blob, "pci3", &pcie3_hose);
-#endif
+ FT_FSL_PCI_SETUP;
+
#ifdef CONFIG_FSL_SGMII_RISER
fsl_sgmii_riser_fdt_fixup(blob);
#endif
+
+#ifdef CONFIG_HAS_FSL_MPH_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
}
#endif