--- /dev/null
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 3) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /*
+ * we use identical timing for all slots. If needed, change the code
+ * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+ */
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[ctrl_num];
+ else
+ pbsp = udimms[ctrl_num];
+
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for data rate %lu MT/s\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
+ if (ctrl_num == CONFIG_DP_DDR_CTRL) {
+ /* force DDR bus width to 32 bits */
+ popts->data_bus_width = 1;
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+ popts->bstopre = 0; /* enable auto precharge */
+ }
+#endif
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
+}
+
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 2,
+ .rank_density = 1073741824u,
+ .capacity = 2147483648,
+ .primary_sdram_width = 64,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 14,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 937,
+ .caslat_x = 0x6FC << 4, /* 14,13,11,10,9,8,7,6 */
+ .taa_ps = 13090,
+ .twr_ps = 15000,
+ .trcd_ps = 13090,
+ .trrd_ps = 5000,
+ .trp_ps = 13090,
+ .tras_ps = 33000,
+ .trc_ps = 46090,
+ .trfc_ps = 160000,
+ .twtr_ps = 7500,
+ .trtp_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tfaw_ps = 25000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if (((controller_number == 0) && (dimm_number == 0)) ||
+ ((controller_number == 1) && (dimm_number == 0))) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+#endif
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing DDR....");
+
+ puts("using SPD\n");
+ dram_size = fsl_ddr_sdram();
+
+ return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ phys_size_t dp_ddr_size;
+#endif
+
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
+ gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+ gd->bd->bi_dram[1].size = gd->ram_size -
+ CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ } else {
+ gd->bd->bi_dram[0].size = gd->ram_size;
+ }
+
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ /* initialize DP-DDR here */
+ puts("DP-DDR: ");
+ /*
+ * DDR controller use 0 as the base address for binding.
+ * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
+ */
+ dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
+ CONFIG_DP_DDR_CTRL,
+ CONFIG_DP_DDR_NUM_CTRLS,
+ CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
+ NULL, NULL, NULL);
+ if (dp_ddr_size) {
+ gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
+ gd->bd->bi_dram[2].size = dp_ddr_size;
+ } else {
+ puts("Not detected");
+ }
+#endif
+}
projects / oweals / u-boot.git / blobdiff