#include <hwconfig.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/soc.h>
+#include <asm/arch-fsl-layerscape/fsl_icid.h>
#include "../common/qixis.h"
#include "ls1088a_qixis.h"
{
int ret;
+#ifndef CONFIG_DM_I2C
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+#else
+ struct udevice *dev;
+
+ ret = i2c_get_chip_for_busnum(0, I2C_MUX_PCA_ADDR_PRI, 1, &dev);
+ if (!ret)
+ ret = dm_i2c_write(dev, 0, &ch, 1);
+#endif
if (ret) {
puts("PCA: failed to select proper channel\n");
return ret;
/* Access to Control/Shared register */
reg = 0x0;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+#else
+ struct udevice *dev;
+
+ i2c_get_chip_for_busnum(0, I2C_RETIMER_ADDR, 1, &dev);
+ dm_i2c_write(dev, 0xff, ®, 1);
+#endif
/* Read device revision and ID */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 1, ®, 1);
+#endif
debug("Retimer version id = 0x%x\n", reg);
/* Enable Broadcast. All writes target all channel register sets */
reg = 0x0c;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0xff, ®, 1);
+#endif
/* Reset Channel Registers */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 0, ®, 1);
+#endif
reg |= 0x4;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0, ®, 1);
+#endif
/* Set data rate as 10.3125 Gbps */
reg = 0x90;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x60, ®, 1);
+#endif
reg = 0xb3;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x61, ®, 1);
+#endif
reg = 0x90;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x62, ®, 1);
+#endif
reg = 0xb3;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x63, ®, 1);
+#endif
reg = 0xcd;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x64, ®, 1);
+#endif
/* Select VCO Divider to full rate (000) */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 0x2F, ®, 1);
+#endif
reg &= 0x0f;
reg |= 0x70;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR, 0x2F, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x2F, ®, 1);
+#endif
#ifdef CONFIG_TARGET_LS1088AQDS
/* Retimer is connected to I2C1_CH5 */
/* Access to Control/Shared register */
reg = 0x0;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
+#else
+ i2c_get_chip_for_busnum(0, I2C_RETIMER_ADDR2, 1, &dev);
+ dm_i2c_write(dev, 0xff, ®, 1);
+#endif
/* Read device revision and ID */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR2, 1, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 1, ®, 1);
+#endif
debug("Retimer version id = 0x%x\n", reg);
/* Enable Broadcast. All writes target all channel register sets */
reg = 0x0c;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0xff, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0xff, ®, 1);
+#endif
/* Reset Channel Registers */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 0, ®, 1);
+#endif
reg |= 0x4;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0, ®, 1);
+#endif
/* Set data rate as 10.3125 Gbps */
reg = 0x90;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x60, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x60, ®, 1);
+#endif
reg = 0xb3;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x61, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x61, ®, 1);
+#endif
reg = 0x90;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x62, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x62, ®, 1);
+#endif
reg = 0xb3;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x63, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x63, ®, 1);
+#endif
reg = 0xcd;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x64, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x64, ®, 1);
+#endif
/* Select VCO Divider to full rate (000) */
+#ifndef CONFIG_DM_I2C
i2c_read(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
+#else
+ dm_i2c_read(dev, 0x2F, ®, 1);
+#endif
reg &= 0x0f;
reg |= 0x70;
+#ifndef CONFIG_DM_I2C
i2c_write(I2C_RETIMER_ADDR2, 0x2F, 1, ®, 1);
+#else
+ dm_i2c_write(dev, 0x2F, ®, 1);
+#endif
+
#endif
/*return the default channel*/
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
QIXIS_WRITE(brdcfg[5], brdcfg5);
}
#endif
+
+#ifdef CONFIG_TARGET_LS1088AQDS
+ u8 brdcfg4, brdcfg5;
+
+ if (hwconfig("dspi-on-board")) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_USBOSC_MASK;
+ brdcfg4 |= BRDCFG4_SPI;
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+
+ brdcfg5 = QIXIS_READ(brdcfg[5]);
+ brdcfg5 &= ~BRDCFG5_SPR_MASK;
+ brdcfg5 |= BRDCFG5_SPI_ON_BOARD;
+ QIXIS_WRITE(brdcfg[5], brdcfg5);
+ } else if (hwconfig("dspi-off-board")) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_USBOSC_MASK;
+ brdcfg4 |= BRDCFG4_SPI;
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+
+ brdcfg5 = QIXIS_READ(brdcfg[5]);
+ brdcfg5 &= ~BRDCFG5_SPR_MASK;
+ brdcfg5 |= BRDCFG5_SPI_OFF_BOARD;
+ QIXIS_WRITE(brdcfg[5], brdcfg5);
+ }
+#endif
return 0;
}
#endif
u8 chan = PWM_CHANNEL0;
/* Select the PAGE 0 using PMBus commands PAGE for VDD */
+#ifndef CONFIG_DM_I2C
ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
PMBUS_CMD_PAGE, 1, &chan, 1);
+#else
+ struct udevice *dev;
+
+ ret = i2c_get_chip_for_busnum(0, I2C_SVDD_MONITOR_ADDR, 1, &dev);
+ if (!ret)
+ ret = dm_i2c_write(dev, PMBUS_CMD_PAGE,
+ &chan, 1);
+#endif
+
if (ret) {
printf("VID: failed to select VDD Page 0\n");
return ret;
}
/* Read the output voltage using PMBus command READ_VOUT */
+#ifndef CONFIG_DM_I2C
ret = i2c_read(I2C_SVDD_MONITOR_ADDR,
PMBUS_CMD_READ_VOUT, 1, (void *)&vcode, 2);
+#else
+ dm_i2c_read(dev, PMBUS_CMD_READ_VOUT, (void *)&vcode, 2);
+#endif
if (ret) {
printf("VID: failed to read the volatge\n");
return ret;
svdd & 0xFF, (svdd & 0xFF00) >> 8};
/* Write the desired voltage code to the SVDD regulator */
+#ifndef CONFIG_DM_I2C
ret = i2c_write(I2C_SVDD_MONITOR_ADDR,
PMBUS_CMD_PAGE_PLUS_WRITE, 1, (void *)&buff, 5);
+#else
+ struct udevice *dev;
+
+ ret = i2c_get_chip_for_busnum(0, I2C_SVDD_MONITOR_ADDR, 1, &dev);
+ if (!ret)
+ ret = dm_i2c_write(dev, PMBUS_CMD_PAGE_PLUS_WRITE,
+ (void *)&buff, 5);
+#endif
if (ret) {
printf("VID: I2C failed to write to the volatge regulator\n");
return -1;
printf("SVDD changing of RDB\n");
/* Read the BRDCFG54 via CLPD */
+#ifndef CONFIG_DM_I2C
ret = i2c_read(CONFIG_SYS_I2C_FPGA_ADDR,
QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+#else
+ struct udevice *dev;
+
+ ret = i2c_get_chip_for_busnum(0, CONFIG_SYS_I2C_FPGA_ADDR, 1, &dev);
+ if (!ret)
+ ret = dm_i2c_read(dev, QIXIS_BRDCFG4_OFFSET,
+ (void *)&brdcfg4, 1);
+#endif
+
if (ret) {
printf("VID: I2C failed to read the CPLD BRDCFG4\n");
return -1;
brdcfg4 = brdcfg4 | 0x08;
/* Write to the BRDCFG4 */
+#ifndef CONFIG_DM_I2C
ret = i2c_write(CONFIG_SYS_I2C_FPGA_ADDR,
QIXIS_BRDCFG4_OFFSET, 1, (void *)&brdcfg4, 1);
+#else
+ ret = dm_i2c_write(dev, QIXIS_BRDCFG4_OFFSET,
+ (void *)&brdcfg4, 1);
+#endif
+
if (ret) {
debug("VID: I2C failed to set the SVDD CPLD BRDCFG4\n");
return -1;
print_ddr_info(0);
}
-#if defined(CONFIG_ARCH_MISC_INIT)
-int arch_misc_init(void)
-{
- return 0;
-}
-#endif
-
#ifdef CONFIG_FSL_MC_ENET
void board_quiesce_devices(void)
{
int ft_board_setup(void *blob, bd_t *bd)
{
int i;
- u64 base[CONFIG_NR_DRAM_BANKS];
- u64 size[CONFIG_NR_DRAM_BANKS];
+ u16 mc_memory_bank = 0;
+
+ u64 *base;
+ u64 *size;
+ u64 mc_memory_base = 0;
+ u64 mc_memory_size = 0;
+ u16 total_memory_banks;
ft_cpu_setup(blob, bd);
+ fdt_fixup_mc_ddr(&mc_memory_base, &mc_memory_size);
+
+ if (mc_memory_base != 0)
+ mc_memory_bank++;
+
+ total_memory_banks = CONFIG_NR_DRAM_BANKS + mc_memory_bank;
+
+ base = calloc(total_memory_banks, sizeof(u64));
+ size = calloc(total_memory_banks, sizeof(u64));
+
/* fixup DT for the two GPP DDR banks */
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
base[i] = gd->bd->bi_dram[i].start;
size[1] = gd->arch.resv_ram - base[1];
#endif
- fdt_fixup_memory_banks(blob, base, size, CONFIG_NR_DRAM_BANKS);
+ if (mc_memory_base != 0) {
+ for (i = 0; i <= total_memory_banks; i++) {
+ if (base[i] == 0 && size[i] == 0) {
+ base[i] = mc_memory_base;
+ size[i] = mc_memory_size;
+ break;
+ }
+ }
+ }
+
+ fdt_fixup_memory_banks(blob, base, size, total_memory_banks);
fdt_fsl_mc_fixup_iommu_map_entry(blob);
#ifdef CONFIG_FSL_MC_ENET
fdt_fixup_board_enet(blob);
#endif
+
+ fdt_fixup_icid(blob);
+
if (is_pb_board())
fixup_ls1088ardb_pb_banner(blob);
}
#endif
+#ifdef CONFIG_ENV_IS_IN_SPI_FLASH
void *env_sf_get_env_addr(void)
{
return (void *)(CONFIG_SYS_FSL_QSPI_BASE + CONFIG_ENV_OFFSET);
}
#endif
+#endif
projects / oweals / u-boot.git / blobdiff