return ddr_size;
}
-typedef struct {
- u32 datarate_mhz_low;
- u32 datarate_mhz_high;
+struct board_specific_parameters {
u32 n_ranks;
+ u32 datarate_mhz_high;
u32 clk_adjust;
u32 wrlvl_start;
u32 cpo;
u32 write_data_delay;
u32 force_2T;
-} board_specific_parameters_t;
+};
-/* ranges for parameters:
- * wr_data_delay = 0-6
- * clk adjust = 0-8
- * cpo 2-0x1E (30)
+/*
+ * This table contains all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
*/
-
-
-/* XXX: these values need to be checked for all interleaving modes. */
-/* XXX: No reliable dual-rank 800 MHz setting has been found. It may
- * seem reliable, but errors will appear when memory intensive
- * program is run. */
-/* XXX: Single rank at 800 MHz is OK. */
-const board_specific_parameters_t board_specific_parameters[][30] = {
- {
+static const struct board_specific_parameters udimm0[] = {
/*
* memory controller 0
- * lo| hi| num| clk| wrlvl | cpo |wrdata|2T
- * mhz| mhz|ranks|adjst| start | delay|
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
*/
- { 0, 850, 4, 4, 6, 0xff, 2, 0},
- {851, 950, 4, 5, 7, 0xff, 2, 0},
- {951, 1050, 4, 5, 8, 0xff, 2, 0},
- {1051, 1250, 4, 5, 10, 0xff, 2, 0},
- {1251, 1350, 4, 5, 11, 0xff, 2, 0},
- { 0, 850, 2, 5, 6, 0xff, 2, 0},
- {851, 950, 2, 5, 7, 0xff, 2, 0},
- {951, 1050, 2, 5, 7, 0xff, 2, 0},
- {1051, 1250, 2, 4, 6, 0xff, 2, 0},
- {1251, 1350, 2, 5, 7, 0xff, 2, 0},
- },
-
- {
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 5, 6, 0xff, 2, 0},
+ {2, 1050, 5, 7, 0xff, 2, 0},
+ {2, 1250, 4, 6, 0xff, 2, 0},
+ {2, 1350, 5, 7, 0xff, 2, 0},
+ {2, 1666, 5, 8, 0xff, 2, 0},
+ {1, 850, 4, 5, 0xff, 2, 0},
+ {1, 950, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The two slots have slightly different timing. The center values are good
+ * for both slots. We use identical speed tables for them. In future use, if
+ * DIMMs have fewer center values that require two separated tables, copy the
+ * udimm0 table to udimm1 and make changes to clk_adjust and wrlvl_start.
+ */
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+ udimm0,
+};
+
+static const struct board_specific_parameters rdimm0[] = {
/*
- * memory controller 1
- * lo| hi| num| clk| wrlvl | cpo |wrdata|2T
- * mhz| mhz|ranks|adjst| start | delay|
+ * memory controller 0
+ * num| hi| clk| wrlvl | cpo |wrdata|2T
+ * ranks| mhz|adjst| start | |delay |
*/
- { 0, 850, 4, 4, 6, 0xff, 2, 0},
- {851, 950, 4, 5, 7, 0xff, 2, 0},
- {951, 1050, 4, 5, 8, 0xff, 2, 0},
- {1051, 1250, 4, 5, 10, 0xff, 2, 0},
- {1251, 1350, 4, 5, 11, 0xff, 2, 0},
- { 0, 850, 2, 5, 6, 0xff, 2, 0},
- {851, 950, 2, 5, 7, 0xff, 2, 0},
- {951, 1050, 2, 5, 7, 0xff, 2, 0},
- {1051, 1250, 2, 4, 6, 0xff, 2, 0},
- {1251, 1350, 2, 5, 7, 0xff, 2, 0},
- }
+ {4, 850, 4, 6, 0xff, 2, 0},
+ {4, 950, 5, 7, 0xff, 2, 0},
+ {4, 1050, 5, 8, 0xff, 2, 0},
+ {4, 1250, 5, 10, 0xff, 2, 0},
+ {4, 1350, 5, 11, 0xff, 2, 0},
+ {4, 1666, 5, 12, 0xff, 2, 0},
+ {2, 850, 4, 6, 0xff, 2, 0},
+ {2, 1050, 4, 7, 0xff, 2, 0},
+ {2, 1666, 4, 8, 0xff, 2, 0},
+ {1, 850, 4, 5, 0xff, 2, 0},
+ {1, 950, 4, 7, 0xff, 2, 0},
+ {1, 1666, 4, 8, 0xff, 2, 0},
+ {}
+};
+
+/*
+ * The two slots have slightly different timing. See comments above.
+ */
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+ rdimm0,
};
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
- const board_specific_parameters_t *pbsp =
- &(board_specific_parameters[ctrl_num][0]);
- u32 num_params = sizeof(board_specific_parameters[ctrl_num]) /
- sizeof(board_specific_parameters[0][0]);
- u32 i;
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
ulong ddr_freq;
+ if (ctrl_num > 1) {
+ printf("Wrong parameter for controller number %d", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[ctrl_num];
+ else
+ pbsp = udimms[ctrl_num];
+
+
/* Get clk_adjust, cpo, write_data_delay,2T, according to the board ddr
* freqency and n_banks specified in board_specific_parameters table.
*/
ddr_freq = get_ddr_freq(0) / 1000000;
- for (i = 0; i < num_params; i++) {
- if (ddr_freq >= pbsp->datarate_mhz_low &&
- ddr_freq <= pbsp->datarate_mhz_high &&
- pdimm[0].n_ranks == pbsp->n_ranks) {
- popts->cpo_override = pbsp->cpo;
- popts->write_data_delay = pbsp->write_data_delay;
- popts->clk_adjust = pbsp->clk_adjust;
- popts->wrlvl_start = pbsp->wrlvl_start;
- popts->twoT_en = pbsp->force_2T;
- break;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->cpo_override = pbsp->cpo;
+ popts->write_data_delay =
+ pbsp->write_data_delay;
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->twoT_en = pbsp->force_2T;
+ goto found;
+ }
+ pbsp_highest = pbsp;
}
pbsp++;
}
- if (i == num_params) {
- printf("Warning: board specific timing not found "
- "for data rate %lu MT/s!\n", ddr_freq);
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found "
+ "for data rate %lu MT/s!\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->cpo_override = pbsp_highest->cpo;
+ popts->write_data_delay = pbsp_highest->write_data_delay;
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->twoT_en = pbsp_highest->force_2T;
+ } else {
+ panic("DIMM is not supported by this board");
}
-
+found:
/*
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed