arm: rmobile: Add Stout board support

[oweals/u-boot.git] / board / davinci / dvevm / dvevm.c

diff --git a/board/davinci/dvevm/dvevm.c b/board/davinci/dvevm/dvevm.c
index abf60b35b085a032c1a4d98c50a97ef9c5498f1f..c34bde4fa6013fbc691be2d7cceb804a34905495 100644 (file)
--- a/board/davinci/dvevm/dvevm.c
+++ b/board/davinci/dvevm/dvevm.c
@@ -8,28 +8,14 @@
  * Copyright (C) 2004 Texas Instruments.
  *
  * ----------------------------------------------------------------------------
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- *  You should have received a copy of the GNU General Public License
- *  along with this program; if not, write to the Free Software
- *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ * SPDX-License-Identifier:    GPL-2.0+
  * ----------------------------------------------------------------------------
  */
 
 #include <common.h>
 #include <i2c.h>
 #include <asm/arch/hardware.h>
-#include <asm/arch/emac_defs.h>
-#include "../common/psc.h"
-#include "../common/misc.h"
+#include <asm/arch/davinci_misc.h>
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -41,41 +27,26 @@ int board_init(void)
        /* address of boot parameters */
        gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
 
-       /* Workaround for TMS320DM6446 errata 1.3.22 */
-       REG(PSC_SILVER_BULLET) = 0;
+       /* Configure AEMIF pins (although this should be configured at boot time
+        * with pull-up/pull-down resistors) */
+       REG(PINMUX0) = 0x00000c1f;
+
+       davinci_errata_workarounds();
 
        /* Power on required peripherals */
-       lpsc_on(DAVINCI_LPSC_EMAC);
-       lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER);
-       lpsc_on(DAVINCI_LPSC_MDIO);
-       lpsc_on(DAVINCI_LPSC_I2C);
-       lpsc_on(DAVINCI_LPSC_UART0);
-       lpsc_on(DAVINCI_LPSC_TIMER1);
        lpsc_on(DAVINCI_LPSC_GPIO);
+       lpsc_on(DAVINCI_LPSC_USB);
 
 #if !defined(CONFIG_SYS_USE_DSPLINK)
        /* Powerup the DSP */
        dsp_on();
 #endif /* CONFIG_SYS_USE_DSPLINK */
 
-       /* Bringup UART0 out of reset */
-       REG(UART0_PWREMU_MGMT) = 0x0000e003;
-
-       /* Enable GIO3.3V cells used for EMAC */
-       REG(VDD3P3V_PWDN) = 0;
-
-       /* Enable UART0 MUX lines */
-       REG(PINMUX1) |= 1;
-
-       /* Enable EMAC and AEMIF pins */
-       REG(PINMUX0) = 0x80000c1f;
-
-       /* Enable I2C pin Mux */
-       REG(PINMUX1) |= (1 << 7);
-
-       /* Set the Bus Priority Register to appropriate value */
-       REG(VBPR) = 0x20;
+       davinci_enable_uart0();
+       davinci_enable_emac();
+       davinci_enable_i2c();
 
+       lpsc_on(DAVINCI_LPSC_TIMER1);
        timer_init();
 
        return(0);
@@ -86,14 +57,9 @@ int misc_init_r(void)
        uint8_t video_mode;
        uint8_t eeprom_enetaddr[6];
 
-       dv_display_clk_infos();
-
        /* Read Ethernet MAC address from EEPROM if available. */
        if (dvevm_read_mac_address(eeprom_enetaddr))
-               dv_configure_mac_address(eeprom_enetaddr);
-
-       if (!eth_hw_init())
-               printf("ethernet init failed!\n");
+               davinci_sync_env_enetaddr(eeprom_enetaddr);
 
        i2c_read(0x39, 0x00, 1, &video_mode, 1);
 
@@ -101,3 +67,25 @@ int misc_init_r(void)
 
        return(0);
 }
+
+#ifdef CONFIG_USB_DAVINCI
+
+/* IO Expander I2C address and USB VBUS enable mask */
+#define IOEXP_I2C_ADDR 0x3A
+#define IOEXP_VBUSEN_MASK 1
+
+/*
+ * This function enables USB VBUS by writting to IO expander using I2C.
+ * Note that the I2C is already initialized at this stage. This
+ * function is used by davinci specific USB wrapper code.
+ */
+void enable_vbus(void)
+{
+       uchar data;  /* IO Expander data to enable VBUS */
+
+       /* Write to IO expander to enable VBUS */
+       i2c_read(IOEXP_I2C_ADDR, 0, 0, &data, 1);
+       data &= ~IOEXP_VBUSEN_MASK;
+       i2c_write(IOEXP_I2C_ADDR, 0, 0, &data, 1);
+}
+#endif