#include <netdev.h>
#include <fdt_support.h>
#include <sata.h>
+#include <splash.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/iomux.h>
+#include <asm/arch/mxc_hdmi.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/sata.h>
+#include <asm/imx-common/video.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <dm/platform_data/serial_mxc.h>
#include "common.h"
#include "../common/eeprom.h"
+#include "../common/common.h"
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_SPLASH_SCREEN
+static struct splash_location cm_fx6_splash_locations[] = {
+ {
+ .name = "sf",
+ .storage = SPLASH_STORAGE_SF,
+ .offset = 0x100000,
+ },
+};
+
+int splash_screen_prepare(void)
+{
+ return splash_source_load(cm_fx6_splash_locations,
+ ARRAY_SIZE(cm_fx6_splash_locations));
+}
+#endif
+
+#ifdef CONFIG_IMX_HDMI
+static void cm_fx6_enable_hdmi(struct display_info_t const *dev)
+{
+ imx_enable_hdmi_phy();
+}
+
+struct display_info_t const displays[] = {
+ {
+ .bus = -1,
+ .addr = 0,
+ .pixfmt = IPU_PIX_FMT_RGB24,
+ .detect = detect_hdmi,
+ .enable = cm_fx6_enable_hdmi,
+ .mode = {
+ .name = "HDMI",
+ .refresh = 60,
+ .xres = 1024,
+ .yres = 768,
+ .pixclock = 40385,
+ .left_margin = 220,
+ .right_margin = 40,
+ .upper_margin = 21,
+ .lower_margin = 7,
+ .hsync_len = 60,
+ .vsync_len = 10,
+ .sync = FB_SYNC_EXT,
+ .vmode = FB_VMODE_NONINTERLACED,
+ }
+ },
+};
+size_t display_count = ARRAY_SIZE(displays);
+
+static void cm_fx6_setup_display(void)
+{
+ struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+ int reg;
+
+ enable_ipu_clock();
+ imx_setup_hdmi();
+ reg = __raw_readl(&mxc_ccm->CCGR3);
+ reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_MASK;
+ writel(reg, &mxc_ccm->CCGR3);
+}
+#else
+static inline void cm_fx6_setup_display(void) {}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
#ifdef CONFIG_DWC_AHSATA
static int cm_fx6_issd_gpios[] = {
/* The order of the GPIOs in the array is important! */
+ CM_FX6_SATA_LDO_EN,
CM_FX6_SATA_PHY_SLP,
CM_FX6_SATA_NRSTDLY,
CM_FX6_SATA_PWREN,
CM_FX6_SATA_NSTANDBY1,
CM_FX6_SATA_NSTANDBY2,
- CM_FX6_SATA_LDO_EN,
};
static void cm_fx6_sata_power(int on)
/* Make sure this gpio has logical 0 value */
gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
udelay(100);
-
- cm_fx6_sata_power(0);
- mdelay(250);
cm_fx6_sata_power(1);
for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
return err;
}
+
+int sata_stop(void)
+{
+ __sata_stop();
+ cm_fx6_sata_power(0);
+ mdelay(250);
+
+ return 0;
+}
#else
static int cm_fx6_setup_issd(void) { return 0; }
#endif
MUX_PAD_CTRL(ENET_PAD_CTRL)),
};
-static int handle_mac_address(void)
+static int handle_mac_address(char *env_var, uint eeprom_bus)
{
unsigned char enetaddr[6];
int rc;
- rc = eth_getenv_enetaddr("ethaddr", enetaddr);
+ rc = eth_getenv_enetaddr(env_var, enetaddr);
if (rc)
return 0;
- rc = cl_eeprom_read_mac_addr(enetaddr);
+ rc = cl_eeprom_read_mac_addr(enetaddr, eeprom_bus);
if (rc)
return rc;
- if (!is_valid_ether_addr(enetaddr))
+ if (!is_valid_ethaddr(enetaddr))
return -1;
- return eth_setenv_enetaddr("ethaddr", enetaddr);
+ return eth_setenv_enetaddr(env_var, enetaddr);
}
+#define SB_FX6_I2C_EEPROM_BUS 0
+#define NO_MAC_ADDR "No MAC address found for %s\n"
int board_eth_init(bd_t *bis)
{
int err;
- err = handle_mac_address();
- if (err)
- puts("No MAC address found\n");
+ if (handle_mac_address("ethaddr", CONFIG_SYS_I2C_EEPROM_BUS))
+ printf(NO_MAC_ADDR, "primary NIC");
+
+ if (handle_mac_address("eth1addr", SB_FX6_I2C_EEPROM_BUS))
+ printf(NO_MAC_ADDR, "secondary NIC");
SETUP_IOMUX_PADS(enet_pads);
/* phy reset */
#endif
#ifdef CONFIG_OF_BOARD_SETUP
-void ft_board_setup(void *blob, bd_t *bd)
+int ft_board_setup(void *blob, bd_t *bd)
{
uint8_t enetaddr[6];
/* MAC addr */
if (eth_getenv_enetaddr("ethaddr", enetaddr)) {
- fdt_find_and_setprop(blob, "/fec", "local-mac-address",
+ fdt_find_and_setprop(blob,
+ "/soc/aips-bus@02100000/ethernet@02188000",
+ "local-mac-address", enetaddr, 6, 1);
+ }
+
+ if (eth_getenv_enetaddr("eth1addr", enetaddr)) {
+ fdt_find_and_setprop(blob, "/eth@pcie", "local-mac-address",
enetaddr, 6, 1);
}
+
+ return 0;
}
#endif
if (ret)
printf("Warning: I2C setup failed: %d\n", ret);
+ cm_fx6_setup_display();
+
return 0;
}