Merge branch 'master' of git://git.denx.de/u-boot-nds32

[oweals/u-boot.git] / board / bf518f-ezbrd / bf518f-ezbrd.c

diff --git a/board/bf518f-ezbrd/bf518f-ezbrd.c b/board/bf518f-ezbrd/bf518f-ezbrd.c
index c2ab598d70d03606560d4f4c607edd5dc4c70ac2..09a2353e7d93f26f730e5691507941ca62c22f93 100644 (file)
--- a/board/bf518f-ezbrd/bf518f-ezbrd.c
+++ b/board/bf518f-ezbrd/bf518f-ezbrd.c
@@ -14,6 +14,7 @@
 #include <spi.h>
 #include <asm/blackfin.h>
 #include <asm/net.h>
+#include <asm/portmux.h>
 #include <asm/mach-common/bits/otp.h>
 #include <asm/sdh.h>
 
@@ -29,24 +30,21 @@ int checkboard(void)
 #if defined(CONFIG_BFIN_MAC)
 static void board_init_enetaddr(uchar *mac_addr)
 {
+#ifdef CONFIG_SYS_NO_FLASH
+# define USE_MAC_IN_FLASH 0
+#else
+# define USE_MAC_IN_FLASH 1
+#endif
        bool valid_mac = false;
 
-#if 0
-       /* the MAC is stored in OTP memory page 0xDF */
-       uint32_t ret;
-       uint64_t otp_mac;
-
-       ret = bfrom_OtpRead(0xDF, OTP_LOWER_HALF, &otp_mac);
-       if (!(ret & OTP_MASTER_ERROR)) {
-               uchar *otp_mac_p = (uchar *)&otp_mac;
-
-               for (ret = 0; ret < 6; ++ret)
-                       mac_addr[ret] = otp_mac_p[5 - ret];
-
-               if (is_valid_ether_addr(mac_addr))
+       if (USE_MAC_IN_FLASH) {
+               /* we cram the MAC in the last flash sector */
+               uchar *board_mac_addr = (uchar *)0x203F0096;
+               if (is_valid_ether_addr(board_mac_addr)) {
+                       memcpy(mac_addr, board_mac_addr, 6);
                        valid_mac = true;
+               }
        }
-#endif
 
        if (!valid_mac) {
                puts("Warning: Generating 'random' MAC address\n");
@@ -56,6 +54,13 @@ static void board_init_enetaddr(uchar *mac_addr)
        eth_setenv_enetaddr("ethaddr", mac_addr);
 }
 
+/* Only the first run of boards had a KSZ switch */
+#if defined(CONFIG_BFIN_SPI) && __SILICON_REVISION__ == 0
+# define KSZ_POSSIBLE 1
+#else
+# define KSZ_POSSIBLE 0
+#endif
+
 #define KSZ_MAX_HZ    5000000
 
 #define KSZ_WRITE     0x02
@@ -108,17 +113,16 @@ static int ksz8893m_reset(struct spi_slave *slave)
        return ret;
 }
 
-int board_eth_init(bd_t *bis)
+static bool board_ksz_init(void)
 {
-       static bool switch_is_alive = false, phy_is_ksz = true;
-       int ret;
+       static bool switch_is_alive = false;
 
        if (!switch_is_alive) {
                struct spi_slave *slave = spi_setup_slave(0, 1, KSZ_MAX_HZ, SPI_MODE_3);
                if (slave) {
                        if (!spi_claim_bus(slave)) {
-                               phy_is_ksz = (ksz8893m_reg_read(slave, KSZ_REG_CHID) == 0x88);
-                               ret = phy_is_ksz ? ksz8893m_reset(slave) : 0;
+                               bool phy_is_ksz = (ksz8893m_reg_read(slave, KSZ_REG_CHID) == 0x88);
+                               int ret = phy_is_ksz ? ksz8893m_reset(slave) : 0;
                                switch_is_alive = (ret == 0);
                                spi_release_bus(slave);
                        }
@@ -126,10 +130,16 @@ int board_eth_init(bd_t *bis)
                }
        }
 
-       if (switch_is_alive)
-               return bfin_EMAC_initialize(bis);
-       else
-               return -1;
+       return switch_is_alive;
+}
+
+int board_eth_init(bd_t *bis)
+{
+       if (KSZ_POSSIBLE) {
+               if (!board_ksz_init())
+                       return 0;
+       }
+       return bfin_EMAC_initialize(bis);
 }
 #endif
 
@@ -141,23 +151,22 @@ int misc_init_r(void)
                board_init_enetaddr(enetaddr);
 #endif
 
+#ifndef CONFIG_SYS_NO_FLASH
+       /* we use the last sector for the MAC address / POST LDR */
+       extern flash_info_t flash_info[];
+       flash_protect(FLAG_PROTECT_SET, 0x203F0000, 0x203FFFFF, &flash_info[0]);
+#endif
+
        return 0;
 }
 
 int board_early_init_f(void)
 {
-#if !defined(CONFIG_SYS_NO_FLASH)
-       /* setup BF518-EZBRD GPIO pin PG11 to AMS2. */
-       bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_6_MASK) | PORT_x_MUX_6_FUNC_2);
-       bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG11);
-
-# if !defined(CONFIG_BFIN_SPI)
-       /* setup BF518-EZBRD GPIO pin PG15 to AMS3. */
-       bfin_write_PORTG_MUX((bfin_read_PORTG_MUX() & ~PORT_x_MUX_7_MASK) | PORT_x_MUX_7_FUNC_3);
-       bfin_write_PORTG_FER(bfin_read_PORTG_FER() | PG15);
-# endif
-#endif
-       return 0;
+       /* connect async banks by default */
+       const unsigned short pins[] = {
+               P_AMS2, P_AMS3, 0,
+       };
+       return peripheral_request_list(pins, "async");
 }
 
 #ifdef CONFIG_BFIN_SDH