#include <asm/arch/at91_common.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/atmel_mpddrc.h>
-#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <asm/arch/sama5d3_smc.h>
#include <asm/arch/sama5d4.h>
-#include <atmel_hlcdc.h>
-#include <atmel_mci.h>
-#include <lcd.h>
-#include <mmc.h>
-#include <net.h>
-#include <netdev.h>
-#include <nand.h>
-#include <spi.h>
-#include <version.h>
+#include <debug_uart.h>
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_ATMEL_SPI
-#ifndef CONFIG_DM_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs == 0;
-}
-#endif
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
-}
-
-static void sama5d4_xplained_spi0_hw_init(void)
-{
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
-
- at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
-
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_SPI0);
-}
-#endif /* CONFIG_ATMEL_SPI */
-
#ifdef CONFIG_NAND_ATMEL
static void sama5d4_xplained_nand_hw_init(void)
{
}
#endif
-#ifdef CONFIG_LCD
-vidinfo_t panel_info = {
- .vl_col = 480,
- .vl_row = 272,
- .vl_clk = 9000000,
- .vl_bpix = LCD_BPP,
- .vl_tft = 1,
- .vl_hsync_len = 41,
- .vl_left_margin = 2,
- .vl_right_margin = 2,
- .vl_vsync_len = 11,
- .vl_upper_margin = 2,
- .vl_lower_margin = 2,
- .mmio = ATMEL_BASE_LCDC,
-};
-
-/* No power up/down pin for the LCD pannel */
-void lcd_enable(void) { /* Empty! */ }
-void lcd_disable(void) { /* Empty! */ }
-
-unsigned int has_lcdc(void)
-{
- return 1;
-}
-
-static void sama5d4_xplained_lcd_hw_init(void)
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
{
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 24, 0); /* LCDPWM */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 25, 0); /* LCDDISP */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 26, 0); /* LCDVSYNC */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 27, 0); /* LCDHSYNC */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 28, 0); /* LCDDOTCK */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 29, 0); /* LCDDEN */
-
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 0, 0); /* LCDD0 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 1, 0); /* LCDD1 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 2, 0); /* LCDD2 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 3, 0); /* LCDD3 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 4, 0); /* LCDD4 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 5, 0); /* LCDD5 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 6, 0); /* LCDD6 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 7, 0); /* LCDD7 */
-
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 8, 0); /* LCDD9 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 9, 0); /* LCDD8 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 10, 0); /* LCDD10 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 11, 0); /* LCDD11 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 12, 0); /* LCDD12 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 13, 0); /* LCDD13 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 14, 0); /* LCDD14 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 15, 0); /* LCDD15 */
-
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 16, 0); /* LCDD16 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 17, 0); /* LCDD17 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 18, 0); /* LCDD18 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 19, 0); /* LCDD19 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 20, 0); /* LCDD20 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 21, 0); /* LCDD21 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 22, 0); /* LCDD22 */
- at91_pio3_set_a_periph(AT91_PIO_PORTA, 23, 0); /* LCDD23 */
-
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_LCDC);
-}
-
-#ifdef CONFIG_LCD_INFO
-void lcd_show_board_info(void)
-{
- ulong dram_size, nand_size;
- int i;
- char temp[32];
-
- lcd_printf("%s\n", U_BOOT_VERSION);
- lcd_printf("2014 ATMEL Corp\n");
- lcd_printf("%s CPU at %s MHz\n", get_cpu_name(),
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
-
- nand_size = 0;
-#ifdef CONFIG_NAND_ATMEL
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i]->size;
+#ifdef CONFIG_DM_VIDEO
+ at91_video_show_board_info();
#endif
- lcd_printf("%ld MB SDRAM, %ld MB NAND\n",
- dram_size >> 20, nand_size >> 20);
-}
-#endif /* CONFIG_LCD_INFO */
-
-#endif /* CONFIG_LCD */
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-void sama5d4_xplained_mci1_hw_init(void)
-{
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 19, 1); /* MCI1 CDA */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 20, 1); /* MCI1 DA0 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 21, 1); /* MCI1 DA1 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 22, 1); /* MCI1 DA2 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 23, 1); /* MCI1 DA3 */
- at91_pio3_set_c_periph(AT91_PIO_PORTE, 18, 0); /* MCI1 CLK */
-
- /*
- * As the mci io internal pull down is too strong, so if the io needs
- * external pull up, the pull up resistor will be very small, if so
- * the power consumption will increase, so disable the interanl pull
- * down to save the power.
- */
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 18, 0);
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 19, 0);
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 20, 0);
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 21, 0);
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 22, 0);
- at91_pio3_set_pio_pulldown(AT91_PIO_PORTE, 23, 0);
-
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_MCI1);
-}
-
-int board_mmc_init(bd_t *bis)
-{
- /* Enable the power supply */
- at91_set_pio_output(AT91_PIO_PORTE, 4, 0);
-
- return atmel_mci_init((void *)ATMEL_BASE_MCI1);
-}
-#endif /* CONFIG_GENERIC_ATMEL_MCI */
-
-#ifdef CONFIG_MACB
-void sama5d4_xplained_macb0_hw_init(void)
-{
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
- at91_pio3_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
-
- /* Enable clock */
- at91_periph_clk_enable(ATMEL_ID_GMAC0);
+ return 0;
}
#endif
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
static void sama5d4_xplained_serial3_hw_init(void)
{
at91_pio3_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */
at91_periph_clk_enable(ATMEL_ID_USART3);
}
+void board_debug_uart_init(void)
+{
+ sama5d4_xplained_serial3_hw_init();
+}
+#endif
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
- at91_periph_clk_enable(ATMEL_ID_PIOD);
- at91_periph_clk_enable(ATMEL_ID_PIOE);
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
+ return 0;
+}
+#endif
- sama5d4_xplained_serial3_hw_init();
+#define AT24MAC_MAC_OFFSET 0x9a
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+#ifdef CONFIG_I2C_EEPROM
+ at91_set_ethaddr(AT24MAC_MAC_OFFSET);
+#endif
return 0;
}
+#endif
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
-#ifdef CONFIG_ATMEL_SPI
- sama5d4_xplained_spi0_hw_init();
-#endif
#ifdef CONFIG_NAND_ATMEL
sama5d4_xplained_nand_hw_init();
#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
- sama5d4_xplained_mci1_hw_init();
-#endif
-#ifdef CONFIG_MACB
- sama5d4_xplained_macb0_hw_init();
-#endif
-#ifdef CONFIG_LCD
- sama5d4_xplained_lcd_hw_init();
-#endif
#ifdef CONFIG_CMD_USB
sama5d4_xplained_usb_hw_init();
#endif
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- at91_udp_hw_init();
-#endif
return 0;
}
return 0;
}
-int board_eth_init(bd_t *bis)
-{
- int rc = 0;
-
-#ifdef CONFIG_MACB
- rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
-#endif
-
-#ifdef CONFIG_USB_GADGET_ATMEL_USBA
- usba_udc_probe(&pdata);
-#ifdef CONFIG_USB_ETH_RNDIS
- usb_eth_initialize(bis);
-#endif
-#endif
-
- return rc;
-}
-
/* SPL */
#ifdef CONFIG_SPL_BUILD
void spl_board_init(void)
{
-#ifdef CONFIG_SYS_USE_MMC
- sama5d4_xplained_mci1_hw_init();
-#elif CONFIG_SYS_USE_NANDFLASH
+#if CONFIG_NAND_BOOT
sama5d4_xplained_nand_hw_init();
-#elif CONFIG_SYS_USE_SERIALFLASH
- sama5d4_xplained_spi0_hw_init();
#endif
}
projects / oweals / u-boot.git / blobdiff