#include <asm/arch/at91_rstc.h>
#include <asm/arch/clk.h>
#include <asm/arch/gpio.h>
-#include <lcd.h>
-#include <atmel_hlcdc.h>
-#include <atmel_mci.h>
-#ifdef CONFIG_MACB
-#include <net.h>
-#endif
-#include <netdev.h>
-#ifdef CONFIG_LCD_INFO
-#include <nand.h>
-#include <version.h>
-#endif
-#ifdef CONFIG_ATMEL_SPI
-#include <spi.h>
-#endif
+#include <debug_uart.h>
+#include <asm/mach-types.h>
DECLARE_GLOBAL_DATA_PTR;
}
#endif
-int board_eth_init(bd_t *bis)
+#ifdef CONFIG_BOARD_LATE_INIT
+int board_late_init(void)
{
- int rc = 0;
-
-#ifdef CONFIG_MACB
- if (has_emac0())
- rc = macb_eth_initialize(0,
- (void *)ATMEL_BASE_EMAC0, 0x00);
- if (has_emac1())
- rc = macb_eth_initialize(1,
- (void *)ATMEL_BASE_EMAC1, 0x00);
+#ifdef CONFIG_DM_VIDEO
+ at91_video_show_board_info();
#endif
- return rc;
-}
-
-#ifdef CONFIG_LCD
-vidinfo_t panel_info = {
- .vl_col = 800,
- .vl_row = 480,
- .vl_clk = 24000000,
- .vl_sync = LCDC_LCDCFG5_HSPOL | LCDC_LCDCFG5_VSPOL,
- .vl_bpix = LCD_BPP,
- .vl_tft = 1,
- .vl_clk_pol = 1,
- .vl_hsync_len = 128,
- .vl_left_margin = 64,
- .vl_right_margin = 64,
- .vl_vsync_len = 2,
- .vl_upper_margin = 22,
- .vl_lower_margin = 21,
- .mmio = ATMEL_BASE_LCDC,
-};
-
-void lcd_enable(void)
-{
- if (has_lcdc())
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 1); /* power up */
-}
-
-void lcd_disable(void)
-{
- if (has_lcdc())
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* power down */
-}
-
-static void at91sam9x5ek_lcd_hw_init(void)
-{
- if (has_lcdc()) {
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 26, 0); /* LCDPWM */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 27, 0); /* LCDVSYNC */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 28, 0); /* LCDHSYNC */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 24, 0); /* LCDDISP */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 29, 0); /* LCDDEN */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 30, 0); /* LCDPCK */
-
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* LCDD0 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* LCDD1 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* LCDD2 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 3, 0); /* LCDD3 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 4, 0); /* LCDD4 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 5, 0); /* LCDD5 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 6, 0); /* LCDD6 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 7, 0); /* LCDD7 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 8, 0); /* LCDD8 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 9, 0); /* LCDD9 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 10, 0); /* LCDD10 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 11, 0); /* LCDD11 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 12, 0); /* LCDD12 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 13, 0); /* LCDD13 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 14, 0); /* LCDD14 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 15, 0); /* LCDD15 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 16, 0); /* LCDD16 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 17, 0); /* LCDD17 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 18, 0); /* LCDD18 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 19, 0); /* LCDD19 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 20, 0); /* LCDD20 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 21, 0); /* LCDD21 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 22, 0); /* LCDD22 */
- at91_pio3_set_a_periph(AT91_PIO_PORTC, 23, 0); /* LCDD23 */
-
- at91_periph_clk_enable(ATMEL_ID_LCDC);
- }
-}
-
-#ifdef CONFIG_LCD_INFO
-void lcd_show_board_info(void)
-{
- ulong dram_size, nand_size;
- int i;
- char temp[32];
-
- if (has_lcdc()) {
- lcd_printf("%s\n", U_BOOT_VERSION);
- lcd_printf("(C) 2012 ATMEL Corp\n");
- lcd_printf("at91support@atmel.com\n");
- lcd_printf("%s CPU at %s MHz\n",
- get_cpu_name(),
- strmhz(temp, get_cpu_clk_rate()));
-
- dram_size = 0;
- for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
- dram_size += gd->bd->bi_dram[i].size;
- nand_size = 0;
- for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
- nand_size += nand_info[i]->size;
- lcd_printf(" %ld MB SDRAM, %ld MB NAND\n",
- dram_size >> 20,
- nand_size >> 20);
- }
-}
-#endif /* CONFIG_LCD_INFO */
-#endif /* CONFIG_LCD */
-
-/* SPI chip select control */
-#ifdef CONFIG_ATMEL_SPI
-int spi_cs_is_valid(unsigned int bus, unsigned int cs)
-{
- return bus == 0 && cs < 2;
-}
-
-void spi_cs_activate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 0);
- break;
- case 0:
- default:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 0);
- break;
- }
-}
-
-void spi_cs_deactivate(struct spi_slave *slave)
-{
- switch (slave->cs) {
- case 1:
- at91_set_pio_output(AT91_PIO_PORTA, 7, 1);
- break;
- case 0:
- default:
- at91_set_pio_output(AT91_PIO_PORTA, 14, 1);
- break;
- }
+ return 0;
}
-#endif /* CONFIG_ATMEL_SPI */
+#endif
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(bd_t *bd)
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+void board_debug_uart_init(void)
{
- at91_mci_hw_init();
-
- return atmel_mci_init((void *)ATMEL_BASE_HSMCI0);
+ at91_seriald_hw_init();
}
#endif
+#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
- at91_seriald_hw_init();
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
return 0;
}
+#endif
int board_init(void)
{
at91sam9x5ek_nand_hw_init();
#endif
-#ifdef CONFIG_ATMEL_SPI
- at91_spi0_hw_init(1 << 4);
-#endif
-
-#ifdef CONFIG_MACB
- at91_macb_hw_init();
-#endif
-
-#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI)
+#if defined(CONFIG_USB_OHCI_NEW) || defined(CONFIG_USB_EHCI_HCD)
at91_uhp_hw_init();
-#endif
-#ifdef CONFIG_LCD
- at91sam9x5ek_lcd_hw_init();
#endif
return 0;
}
void at91_spl_board_init(void)
{
-#ifdef CONFIG_SYS_USE_MMC
+#ifdef CONFIG_SD_BOOT
at91_mci_hw_init();
-#elif CONFIG_SYS_USE_NANDFLASH
+#elif CONFIG_NAND_BOOT
at91sam9x5ek_nand_hw_init();
-#elif CONFIG_SYS_USE_SPIFLASH
- at91_spi0_hw_init(1 << 4);
#endif
}
projects / oweals / u-boot.git / blobdiff