*/
#include <common.h>
+#include <asm/sizes.h>
#include <asm/arch/at91sam9263.h>
#include <asm/arch/at91sam9263_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/io.h>
+#include <lcd.h>
+#include <atmel_lcdc.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
/* Configure SMC CS3 for NAND/SmartMedia */
at91_sys_write(AT91_SMC_SETUP(3),
- AT91_SMC_NWESETUP_(0) | AT91_SMC_NCS_WRSETUP_(0) |
- AT91_SMC_NRDSETUP_(0) | AT91_SMC_NCS_RDSETUP_(0));
+ AT91_SMC_NWESETUP_(1) | AT91_SMC_NCS_WRSETUP_(0) |
+ AT91_SMC_NRDSETUP_(1) | AT91_SMC_NCS_RDSETUP_(0));
at91_sys_write(AT91_SMC_PULSE(3),
AT91_SMC_NWEPULSE_(3) | AT91_SMC_NCS_WRPULSE_(3) |
AT91_SMC_NRDPULSE_(3) | AT91_SMC_NCS_RDPULSE_(3));
/* Need to reset PHY -> 500ms reset */
at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
- AT91_RSTC_ERSTL | (0x0D << 8) |
+ (AT91_RSTC_ERSTL & (0x0D << 8)) |
AT91_RSTC_URSTEN);
at91_sys_write(AT91_RSTC_CR, AT91_RSTC_KEY | AT91_RSTC_EXTRST);
/* Wait for end hardware reset */
while (!(at91_sys_read(AT91_RSTC_SR) & AT91_RSTC_NRSTL));
+ /* Restore NRST value */
+ at91_sys_write(AT91_RSTC_MR, AT91_RSTC_KEY |
+ (AT91_RSTC_ERSTL & (0x0 << 8)) |
+ AT91_RSTC_URSTEN);
+
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PC25),
pin_to_controller(AT91_PIN_PC0) + PIO_PUER);
}
#endif
+#ifdef CONFIG_LCD
+vidinfo_t panel_info = {
+ vl_col: 240,
+ vl_row: 320,
+ vl_clk: 4965000,
+ vl_sync: ATMEL_LCDC_INVLINE_INVERTED |
+ ATMEL_LCDC_INVFRAME_INVERTED,
+ vl_bpix: 3,
+ vl_tft: 1,
+ vl_hsync_len: 5,
+ vl_left_margin: 1,
+ vl_right_margin:33,
+ vl_vsync_len: 1,
+ vl_upper_margin:1,
+ vl_lower_margin:0,
+ mmio: AT91SAM9263_LCDC_BASE,
+};
+
+void lcd_enable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA30, 1); /* power up */
+}
+
+void lcd_disable(void)
+{
+ at91_set_gpio_value(AT91_PIN_PA30, 0); /* power down */
+}
+
+static void at91sam9263ek_lcd_hw_init(void)
+{
+ at91_set_A_periph(AT91_PIN_PC1, 0); /* LCDHSYNC */
+ at91_set_A_periph(AT91_PIN_PC2, 0); /* LCDDOTCK */
+ at91_set_A_periph(AT91_PIN_PC3, 0); /* LCDDEN */
+ at91_set_B_periph(AT91_PIN_PB9, 0); /* LCDCC */
+ at91_set_A_periph(AT91_PIN_PC6, 0); /* LCDD2 */
+ at91_set_A_periph(AT91_PIN_PC7, 0); /* LCDD3 */
+ at91_set_A_periph(AT91_PIN_PC8, 0); /* LCDD4 */
+ at91_set_A_periph(AT91_PIN_PC9, 0); /* LCDD5 */
+ at91_set_A_periph(AT91_PIN_PC10, 0); /* LCDD6 */
+ at91_set_A_periph(AT91_PIN_PC11, 0); /* LCDD7 */
+ at91_set_A_periph(AT91_PIN_PC14, 0); /* LCDD10 */
+ at91_set_A_periph(AT91_PIN_PC15, 0); /* LCDD11 */
+ at91_set_A_periph(AT91_PIN_PC16, 0); /* LCDD12 */
+ at91_set_B_periph(AT91_PIN_PC12, 0); /* LCDD13 */
+ at91_set_A_periph(AT91_PIN_PC18, 0); /* LCDD14 */
+ at91_set_A_periph(AT91_PIN_PC19, 0); /* LCDD15 */
+ at91_set_A_periph(AT91_PIN_PC22, 0); /* LCDD18 */
+ at91_set_A_periph(AT91_PIN_PC23, 0); /* LCDD19 */
+ at91_set_A_periph(AT91_PIN_PC24, 0); /* LCDD20 */
+ at91_set_B_periph(AT91_PIN_PC17, 0); /* LCDD21 */
+ at91_set_A_periph(AT91_PIN_PC26, 0); /* LCDD22 */
+ at91_set_A_periph(AT91_PIN_PC27, 0); /* LCDD23 */
+
+ at91_sys_write(AT91_PMC_PCER, 1 << AT91SAM9263_ID_LCDC);
+
+ gd->fb_base = AT91SAM9263_SRAM0_BASE;
+}
+#endif
+
int board_init(void)
{
/* Enable Ctrlc */
#endif
#ifdef CONFIG_USB_OHCI_NEW
at91sam9263ek_uhp_hw_init();
+#endif
+#ifdef CONFIG_LCD
+ at91sam9263ek_lcd_hw_init();
#endif
return 0;
}