DECLARE_GLOBAL_DATA_PTR;
+#define CFG_BCSR3_PCIE 0x10
+
+#define BOARD_CANYONLANDS_PCIE 1
+#define BOARD_CANYONLANDS_SATA 2
+#define BOARD_GLACIER 3
+
int board_early_init_f(void)
{
u32 sdr0_cust0;
+ u32 pvr = get_pvr();
- /*------------------------------------------------------------------+
+ /*
* Setup the interrupt controller polarities, triggers, etc.
- *------------------------------------------------------------------*/
+ */
mtdcr(uic0sr, 0xffffffff); /* clear all */
mtdcr(uic0er, 0x00000000); /* disable all */
mtdcr(uic0cr, 0x00000005); /* ATI & UIC1 crit are critical */
mtdcr(AHB_TOP, 0x8000004B);
mtdcr(AHB_BOT, 0x8000004B);
- /*
- * Configure USB-STP pins as alternate and not GPIO
- * It seems to be neccessary to configure the STP pins as GPIO
- * input at powerup (perhaps while USB reset is asserted). So
- * we configure those pins to their "real" function now.
- */
- gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1);
- gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1);
+ if ((pvr == PVR_460EX_RA) || (pvr == PVR_460EX_SE_RA)) {
+ /*
+ * Configure USB-STP pins as alternate and not GPIO
+ * It seems to be neccessary to configure the STP pins as GPIO
+ * input at powerup (perhaps while USB reset is asserted). So
+ * we configure those pins to their "real" function now.
+ */
+ gpio_config(16, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1);
+ gpio_config(19, GPIO_OUT, GPIO_ALT1, GPIO_OUT_1);
+ }
return 0;
}
-int checkboard (void)
+static void canyonlands_sata_init(int board_type)
+{
+ u32 reg;
+
+ if (board_type == BOARD_CANYONLANDS_SATA) {
+ /* Put SATA in reset */
+ SDR_WRITE(SDR0_SRST1, 0x00020001);
+
+ /* Set the phy for SATA, not PCI-E port 0 */
+ reg = SDR_READ(PESDR0_PHY_CTL_RST);
+ SDR_WRITE(PESDR0_PHY_CTL_RST, (reg & 0xeffffffc) | 0x00000001);
+ reg = SDR_READ(PESDR0_L0CLK);
+ SDR_WRITE(PESDR0_L0CLK, (reg & 0xfffffff8) | 0x00000007);
+ SDR_WRITE(PESDR0_L0CDRCTL, 0x00003111);
+ SDR_WRITE(PESDR0_L0DRV, 0x00000104);
+
+ /* Bring SATA out of reset */
+ SDR_WRITE(SDR0_SRST1, 0x00000000);
+ }
+}
+
+int checkboard(void)
{
char *s = getenv("serial#");
u32 pvr = get_pvr();
- if ((pvr == PVR_460GT_RA) || (pvr == PVR_460GT_SE_RA))
+ if ((pvr == PVR_460GT_RA) || (pvr == PVR_460GT_SE_RA)) {
printf("Board: Glacier - AMCC PPC460GT Evaluation Board");
- else
+ gd->board_type = BOARD_GLACIER;
+ } else {
printf("Board: Canyonlands - AMCC PPC460EX Evaluation Board");
+ if (in_8((void *)(CFG_BCSR_BASE + 3)) & CFG_BCSR3_PCIE)
+ gd->board_type = BOARD_CANYONLANDS_PCIE;
+ else
+ gd->board_type = BOARD_CANYONLANDS_SATA;
+ }
+
+ switch (gd->board_type) {
+ case BOARD_CANYONLANDS_PCIE:
+ case BOARD_GLACIER:
+ puts(", 2*PCIe");
+ break;
+
+ case BOARD_CANYONLANDS_SATA:
+ puts(", 1*PCIe/1*SATA");
+ break;
+ }
+
+ printf(", Rev. %X", in_8((void *)(CFG_BCSR_BASE + 0)));
if (s != NULL) {
puts(", serial# ");
}
putc('\n');
+ canyonlands_sata_init(gd->board_type);
+
return (0);
}
}
#endif
-/*************************************************************************
+/*
* pci_target_init
*
* The bootstrap configuration provides default settings for the pci
* inbound map (PIM). But the bootstrap config choices are limited and
* may not be sufficient for a given board.
- *
- ************************************************************************/
+ */
#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
void pci_target_init(struct pci_controller * hose )
{
- /*-------------------------------------------------------------------+
+ /*
* Disable everything
- *-------------------------------------------------------------------*/
+ */
out_le32((void *)PCIX0_PIM0SA, 0); /* disable */
out_le32((void *)PCIX0_PIM1SA, 0); /* disable */
out_le32((void *)PCIX0_PIM2SA, 0); /* disable */
out_le32((void *)PCIX0_EROMBA, 0); /* disable expansion rom */
- /*-------------------------------------------------------------------+
+ /*
* Map all of SDRAM to PCI address 0x0000_0000. Note that the 440
* strapping options to not support sizes such as 128/256 MB.
- *-------------------------------------------------------------------*/
+ */
out_le32((void *)PCIX0_PIM0LAL, CFG_SDRAM_BASE);
out_le32((void *)PCIX0_PIM0LAH, 0);
out_le32((void *)PCIX0_PIM0SA, ~(gd->ram_size - 1) | 1);
out_le32((void *)PCIX0_BAR0, 0);
- /*-------------------------------------------------------------------+
+ /*
* Program the board's subsystem id/vendor id
- *-------------------------------------------------------------------*/
+ */
out_le16((void *)PCIX0_SBSYSVID, CFG_PCI_SUBSYS_VENDORID);
out_le16((void *)PCIX0_SBSYSID, CFG_PCI_SUBSYS_DEVICEID);
int ret = 0;
char *env;
unsigned int delay;
+ int start;
/*
* assume we're called after the PCIX hose is initialized, which takes
* bus ID 0 and therefore start numbering PCIe's from 1.
*/
bus = busno;
- for (i = 0; i <= 1; i++) {
+
+ /*
+ * Canyonlands with SATA enabled has only one PCIe slot
+ * (2nd one).
+ */
+ if (gd->board_type == BOARD_CANYONLANDS_SATA)
+ start = 1;
+ else
+ start = 0;
+
+ for (i = start; i <= 1; i++) {
if (is_end_point(i))
ret = ppc4xx_init_pcie_endport(i);
{
u32 sdr0_srst1 = 0;
u32 eth_cfg;
+ u32 pvr = get_pvr();
/*
* Set EMAC mode/configuration (GMII, SGMII, RGMII...).
/* Set the for 2 RGMII mode */
/* GMC0 EMAC4_0, GMC0 EMAC4_1, RGMII Bridge 0 */
eth_cfg &= ~SDR0_ETH_CFG_GMC0_BRIDGE_SEL;
- eth_cfg |= SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
+ if ((pvr == PVR_460EX_RA) || (pvr == PVR_460EX_SE_RA))
+ eth_cfg |= SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
+ else
+ eth_cfg &= ~SDR0_ETH_CFG_GMC1_BRIDGE_SEL;
mtsdr(SDR0_ETH_CFG, eth_cfg);
/*
/* Fixup NOR mapping */
val[0] = 0; /* chip select number */
val[1] = 0; /* always 0 */
- val[2] = gd->bd->bi_flashstart;
+ val[2] = CFG_FLASH_BASE_PHYS_L; /* we fixed up this address */
val[3] = gd->bd->bi_flashsize;
rc = fdt_find_and_setprop(blob, "/plb/opb/ebc", "ranges",
val, sizeof(val), 1);
projects / oweals / u-boot.git / blobdiff