/*
** Note 1: In this file, you have to provide the following functions:
** ------
-** int board_pre_init(void)
+** int board_early_init_f(void)
** int checkboard(void)
-** long int initdram(int board_type)
+** phys_size_t initdram(int board_type)
** called from 'board_init_f()' into 'common/board.c'
**
** void reset_phy(void)
#define _NOT_USED_ 0xFFFFFFFF
-const uint init_sdram_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04,
- 0xFFFFFC04, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMA RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */
- /*
- * Burst Read. (Offset 8 in UPMA RAM)
- */
- 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04,
- 0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */
- /*
- * Burst Write. (Offset 20 in UPMA RAM)
- */
- 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34,
- 0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */
+const uint init_sdram_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPMA RAM)
+ */
+ 0x0FFCCC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04,
+ 0xFFFFFC04, /* last */
+ /*
+ * SDRAM Initialization (offset 5 in UPMA RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPMA RAM)
+ */
+ 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, /* last */
+ /*
+ * Single Write. (Offset 18 in UPMA RAM)
+ */
+ 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04, 0x0FFC3C04,
+ 0xFFFFFC04, 0xFFFFFC04, 0x0FFFFC04, 0xFFFFFC04, /* last */
+ /*
+ * Burst Write. (Offset 20 in UPMA RAM)
+ */
+ 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC04, 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC34, 0x0FAC0C34,
+ 0xFFFFFC05, 0xFFFFFC04, 0x0FFCFC04, 0xFFFFFC05, /* last */
};
-const uint sdram_table[] =
-{
- /*
- * Single Read. (Offset 0 in UPMA RAM)
- */
- 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
- 0xFF0FFC00, /* last */
- /*
- * SDRAM Initialization (offset 5 in UPMA RAM)
- *
- * This is no UPM entry point. The following definition uses
- * the remaining space to establish an initialization
- * sequence, which is executed by a RUN command.
- *
- */
- 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */
- /*
- * Burst Read. (Offset 8 in UPMA RAM)
- */
- 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
- 0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00,
- 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
- 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
- /*
- * Single Write. (Offset 18 in UPMA RAM)
- */
- 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00,
- 0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */
- _NOT_USED_,
- /*
- * Burst Write. (Offset 20 in UPMA RAM)
- */
- 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00,
- 0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04,
- 0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
- 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
- /*
- * Refresh (Offset 30 in UPMA RAM)
- */
- 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
- 0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_,
- 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
- /*
- * Exception. (Offset 3c in UPMA RAM)
- */
- 0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */
+const uint sdram_table[] = {
+ /*
+ * Single Read. (Offset 0 in UPMA RAM)
+ */
+ 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
+ 0xFF0FFC00, /* last */
+ /*
+ * SDRAM Initialization (offset 5 in UPMA RAM)
+ *
+ * This is no UPM entry point. The following definition uses
+ * the remaining space to establish an initialization
+ * sequence, which is executed by a RUN command.
+ *
+ */
+ 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC05, /* last */
+ /*
+ * Burst Read. (Offset 8 in UPMA RAM)
+ */
+ 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF3C04,
+ 0xF00FFC00, 0xF00FFC00, 0xF00FFC00, 0xFF0FFC00,
+ 0x0FFCCC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
+ 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
+ /*
+ * Single Write. (Offset 18 in UPMA RAM)
+ */
+ 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC04, 0x00AF0C00,
+ 0xFF0FFC04, 0x0FFCCC04, 0xFFAFFC05, /* last */
+ _NOT_USED_,
+ /*
+ * Burst Write. (Offset 20 in UPMA RAM)
+ */
+ 0x0F0FFC24, 0x0F0CFC04, 0xFF0FFC00, 0x00AF0C00,
+ 0xF00FFC00, 0xF00FFC00, 0xF00FFC04, 0x0FFCCC04,
+ 0xFFAFFC04, 0xFFAFFC05, 0xFFAFFC04, 0xFFAFFC04,
+ 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
+ /*
+ * Refresh (Offset 30 in UPMA RAM)
+ */
+ 0x0FFC3C04, 0xFFFFFC04, 0xFFFFFC04, 0xFFFFFC04,
+ 0xFFFFFC05, 0xFFFFFC04, 0xFFFFFC05, _NOT_USED_,
+ 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, 0xFFAFFC04, /* last */
+ /*
+ * Exception. (Offset 3c in UPMA RAM)
+ */
+ 0x0FFFFC34, 0x0FAC0C34, 0xFFFFFC05, 0xFFAFFC04, /* last */
};
/* ------------------------------------------------------------------------- */
-#define CFG_PC4 0x0800
+#define CONFIG_SYS_PC4 0x0800
-#define CFG_DS1 CFG_PC4
+#define CONFIG_SYS_DS1 CONFIG_SYS_PC4
/*
* Very early board init code (fpga boot, etc.)
*/
-int
-board_pre_init (void)
+int board_early_init_f (void)
{
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
- /*
- * Light up the red led on ELPT860 pcb (DS1) (PCDAT)
- */
- immr->im_ioport.iop_pcdat &= ~CFG_DS1; /* PCDAT (DS1 = 0) */
- immr->im_ioport.iop_pcpar &= ~CFG_DS1; /* PCPAR (0=general purpose I/O) */
- immr->im_ioport.iop_pcdir |= CFG_DS1; /* PCDIR (I/O: 0=input, 1=output) */
+ /*
+ * Light up the red led on ELPT860 pcb (DS1) (PCDAT)
+ */
+ immr->im_ioport.iop_pcdat &= ~CONFIG_SYS_DS1; /* PCDAT (DS1 = 0) */
+ immr->im_ioport.iop_pcpar &= ~CONFIG_SYS_DS1; /* PCPAR (0=general purpose I/O) */
+ immr->im_ioport.iop_pcdir |= CONFIG_SYS_DS1; /* PCDIR (I/O: 0=input, 1=output) */
- return ( 0 ); /* success */
+ return (0); /* success */
}
/*
* Return 1 if no second DRAM bank, otherwise returns 0
*/
-int
-checkboard (void)
+int checkboard (void)
{
- unsigned char *s = getenv("serial#");
+ char buf[64];
+ int i = getenv_f("serial#", buf, sizeof(buf));
+
+ if ((i < 0) || strncmp(buf, "ELPT860", 7))
+ printf ("### No HW ID - assuming ELPT860\n");
- if ( !s || strncmp(s, "ELPT860", 7) )
- printf ("### No HW ID - assuming ELPT860\n");
-
- return ( 0 ); /* success */
+ return (0); /* success */
}
/* ------------------------------------------------------------------------- */
-long int
-initdram (int board_type)
+phys_size_t initdram (int board_type)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- long int size8, size9;
- long int size_b0 = 0;
-
- /*
- * This sequence initializes SDRAM chips on ELPT860 board
- */
- upmconfig(UPMA, (uint *)init_sdram_table,
- sizeof(init_sdram_table)/sizeof(uint));
-
- memctl->memc_mptpr = 0x0200;
- memctl->memc_mamr = 0x18002111;
-
- memctl->memc_mar = 0x00000088;
- memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */
-
- upmconfig(UPMA, (uint *)sdram_table,
- sizeof(sdram_table)/sizeof(uint));
-
- /*
- * Preliminary prescaler for refresh (depends on number of
- * banks): This value is selected for four cycles every 62.4 us
- * with two SDRAM banks or four cycles every 31.2 us with one
- * bank. It will be adjusted after memory sizing.
- */
- memctl->memc_mptpr = CFG_MPTPR_2BK_8K;
-
- /*
- * The following value is used as an address (i.e. opcode) for
- * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
- * the port size is 32bit the SDRAM does NOT "see" the lower two
- * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
- * MICRON SDRAMs:
- * -> 0 00 010 0 010
- * | | | | +- Burst Length = 4
- * | | | +----- Burst Type = Sequential
- * | | +------- CAS Latency = 2
- * | +----------- Operating Mode = Standard
- * +-------------- Write Burst Mode = Programmed Burst Length
- */
- memctl->memc_mar = 0x00000088;
-
- /*
- * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
- * preliminary addresses - these have to be modified after the
- * SDRAM size has been determined.
- */
- memctl->memc_or1 = CFG_OR1_PRELIM;
- memctl->memc_br1 = CFG_BR1_PRELIM;
-
- memctl->memc_mamr = CFG_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
-
- udelay (200);
-
- /* perform SDRAM initializsation sequence */
-
- memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */
- udelay (1);
- memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */
- udelay (1);
-
- memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
-
- udelay (1000);
-
- /*
- * Check Bank 0 Memory Size for re-configuration
- *
- * try 8 column mode
- */
- size8 = dram_size (CFG_MAMR_8COL,
- (ulong *) SDRAM_BASE1_PRELIM,
- SDRAM_MAX_SIZE);
-
- udelay (1000);
-
- /*
- * try 9 column mode
- */
- size9 = dram_size (CFG_MAMR_9COL,
- (ulong *) SDRAM_BASE1_PRELIM,
- SDRAM_MAX_SIZE);
-
- if ( size8 < size9 ) /* leave configuration at 9 columns */
- {
- size_b0 = size9;
- /* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
- }
- else /* back to 8 columns */
- {
- size_b0 = size8;
- memctl->memc_mamr = CFG_MAMR_8COL;
- udelay (500);
- /* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
- }
-
- udelay (1000);
-
- /*
- * Adjust refresh rate depending on SDRAM type, both banks
- * For types > 128 MBit leave it at the current (fast) rate
- */
- if ( size_b0 < 0x02000000 )
- {
- /* reduce to 15.6 us (62.4 us / quad) */
- memctl->memc_mptpr = CFG_MPTPR_2BK_4K;
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+ long int size8, size9;
+ long int size_b0 = 0;
+
+ /*
+ * This sequence initializes SDRAM chips on ELPT860 board
+ */
+ upmconfig (UPMA, (uint *) init_sdram_table,
+ sizeof (init_sdram_table) / sizeof (uint));
+
+ memctl->memc_mptpr = 0x0200;
+ memctl->memc_mamr = 0x18002111;
+
+ memctl->memc_mar = 0x00000088;
+ memctl->memc_mcr = 0x80002000; /* CS1: SDRAM bank 0 */
+
+ upmconfig (UPMA, (uint *) sdram_table,
+ sizeof (sdram_table) / sizeof (uint));
+
+ /*
+ * Preliminary prescaler for refresh (depends on number of
+ * banks): This value is selected for four cycles every 62.4 us
+ * with two SDRAM banks or four cycles every 31.2 us with one
+ * bank. It will be adjusted after memory sizing.
+ */
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_8K;
+
+ /*
+ * The following value is used as an address (i.e. opcode) for
+ * the LOAD MODE REGISTER COMMAND during SDRAM initialisation. If
+ * the port size is 32bit the SDRAM does NOT "see" the lower two
+ * address lines, i.e. mar=0x00000088 -> opcode=0x00000022 for
+ * MICRON SDRAMs:
+ * -> 0 00 010 0 010
+ * | | | | +- Burst Length = 4
+ * | | | +----- Burst Type = Sequential
+ * | | +------- CAS Latency = 2
+ * | +----------- Operating Mode = Standard
+ * +-------------- Write Burst Mode = Programmed Burst Length
+ */
+ memctl->memc_mar = 0x00000088;
+
+ /*
+ * Map controller banks 2 and 3 to the SDRAM banks 2 and 3 at
+ * preliminary addresses - these have to be modified after the
+ * SDRAM size has been determined.
+ */
+ memctl->memc_or1 = CONFIG_SYS_OR1_PRELIM;
+ memctl->memc_br1 = CONFIG_SYS_BR1_PRELIM;
+
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL & (~(MAMR_PTAE)); /* no refresh yet */
+
+ udelay (200);
+
+ /* perform SDRAM initializsation sequence */
+
+ memctl->memc_mcr = 0x80002105; /* CS1: SDRAM bank 0 */
+ udelay (1);
+ memctl->memc_mcr = 0x80002230; /* CS1: SDRAM bank 0 - execute twice */
+ udelay (1);
+
+ memctl->memc_mamr |= MAMR_PTAE; /* enable refresh */
+
+ udelay (1000);
+
+ /*
+ * Check Bank 0 Memory Size for re-configuration
+ *
+ * try 8 column mode
+ */
+ size8 = dram_size (CONFIG_SYS_MAMR_8COL,
+ SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
+
+ udelay (1000);
+
+ /*
+ * try 9 column mode
+ */
+ size9 = dram_size (CONFIG_SYS_MAMR_9COL,
+ SDRAM_BASE1_PRELIM, SDRAM_MAX_SIZE);
+
+ if (size8 < size9) { /* leave configuration at 9 columns */
+ size_b0 = size9;
+ /* debug ("SDRAM Bank 0 in 9 column mode: %ld MB\n", size >> 20); */
+ } else { /* back to 8 columns */
+
+ size_b0 = size8;
+ memctl->memc_mamr = CONFIG_SYS_MAMR_8COL;
+ udelay (500);
+ /* debug ("SDRAM Bank 0 in 8 column mode: %ld MB\n", size >> 20); */
+ }
+
udelay (1000);
- }
-
- /*
- * Final mapping: map bigger bank first
- */
- memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CFG_OR_TIMING_SDRAM;
- memctl->memc_br1 = (CFG_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
-
- {
- unsigned long reg;
-
- /* adjust refresh rate depending on SDRAM type, one bank */
- reg = memctl->memc_mptpr;
- reg >>= 1; /* reduce to CFG_MPTPR_1BK_8K / _4K */
- memctl->memc_mptpr = reg;
- }
-
- udelay(10000);
-
- return (size_b0);
+
+ /*
+ * Adjust refresh rate depending on SDRAM type, both banks
+ * For types > 128 MBit leave it at the current (fast) rate
+ */
+ if (size_b0 < 0x02000000) {
+ /* reduce to 15.6 us (62.4 us / quad) */
+ memctl->memc_mptpr = CONFIG_SYS_MPTPR_2BK_4K;
+ udelay (1000);
+ }
+
+ /*
+ * Final mapping: map bigger bank first
+ */
+ memctl->memc_or1 = ((-size_b0) & 0xFFFF0000) | CONFIG_SYS_OR_TIMING_SDRAM;
+ memctl->memc_br1 = (CONFIG_SYS_SDRAM_BASE & BR_BA_MSK) | BR_MS_UPMA | BR_V;
+
+ {
+ unsigned long reg;
+
+ /* adjust refresh rate depending on SDRAM type, one bank */
+ reg = memctl->memc_mptpr;
+ reg >>= 1; /* reduce to CONFIG_SYS_MPTPR_1BK_8K / _4K */
+ memctl->memc_mptpr = reg;
+ }
+
+ udelay (10000);
+
+ return (size_b0);
}
/* ------------------------------------------------------------------------- */
* - short between data lines
*/
-static long int
-dram_size (long int mamr_value,
- long int *base,
- long int maxsize)
+static long int
+dram_size (long int mamr_value, long int *base, long int maxsize)
{
- volatile immap_t *immap = (immap_t *)CFG_IMMR;
- volatile memctl8xx_t *memctl = &immap->im_memctl;
- volatile long int *addr;
- ulong cnt, val;
- ulong save[32]; /* to make test non-destructive */
- unsigned char i = 0;
-
- memctl->memc_mamr = mamr_value;
-
- for (cnt = maxsize/sizeof(long); cnt > 0; cnt >>= 1)
- {
- addr = base + cnt; /* pointer arith! */
-
- save[i++] = *addr;
- *addr = ~cnt;
- }
-
- /* write 0 to base address */
- addr = base;
- save[i] = *addr;
- *addr = 0;
-
- /* check at base address */
- if ( (val = *addr) != 0 )
- {
- *addr = save[i];
-
- return (0);
- }
-
- for (cnt = 1; cnt <= maxsize/sizeof(long); cnt <<= 1)
- {
- addr = base + cnt; /* pointer arith! */
-
- val = *addr;
- *addr = save[--i];
-
- if ( val != (~cnt) )
- {
- return (cnt * sizeof(long));
- }
- }
+ volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
+ volatile memctl8xx_t *memctl = &immap->im_memctl;
+
+ memctl->memc_mamr = mamr_value;
- return (maxsize);
+ return (get_ram_size (base, maxsize));
}
/* ------------------------------------------------------------------------- */
-#define CFG_PA1 0x4000
-#define CFG_PA2 0x2000
+#define CONFIG_SYS_PA1 0x4000
+#define CONFIG_SYS_PA2 0x2000
-#define CFG_LBKs (CFG_PA2 | CFG_PA1)
+#define CONFIG_SYS_LBKs (CONFIG_SYS_PA2 | CONFIG_SYS_PA1)
-void
-reset_phy (void)
+void reset_phy (void)
{
- volatile immap_t *immr = (immap_t *) CFG_IMMR;
-
- /*
- * Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect
- * and no AUI loopback
- */
- immr->im_ioport.iop_padat &= ~CFG_LBKs; /* PADAT (LBK eth 1&2 = 0) */
- immr->im_ioport.iop_papar &= ~CFG_LBKs; /* PAPAR (0=general purpose I/O) */
- immr->im_ioport.iop_padir |= CFG_LBKs; /* PADIR (I/O: 0=input, 1=output) */
+ volatile immap_t *immr = (immap_t *) CONFIG_SYS_IMMR;
+
+ /*
+ * Ensure LBK LXT901 ethernet 1 & 2 = 0 ... for normal loopback in effect
+ * and no AUI loopback
+ */
+ immr->im_ioport.iop_padat &= ~CONFIG_SYS_LBKs; /* PADAT (LBK eth 1&2 = 0) */
+ immr->im_ioport.iop_papar &= ~CONFIG_SYS_LBKs; /* PAPAR (0=general purpose I/O) */
+ immr->im_ioport.iop_padir |= CONFIG_SYS_LBKs; /* PADIR (I/O: 0=input, 1=output) */
}
projects / oweals / u-boot.git / blobdiff