Merge branch 'master' of git://git.denx.de/u-boot

[oweals/u-boot.git] / arch / x86 / include / asm / pci.h

diff --git a/arch/x86/include/asm/pci.h b/arch/x86/include/asm/pci.h
index 6b161881e74513aa6169673266dd66ac6de11808..f7e968e0b0d34192d2cf12f9adeedfa78046f468 100644 (file)
--- a/arch/x86/include/asm/pci.h
+++ b/arch/x86/include/asm/pci.h
@@ -1,4 +1,3 @@
-
 /*
  * (C) Copyright 2002
  * Daniel Engström, Omicron Ceti AB, daniel@omicron.se
@@ -9,8 +8,75 @@
 #ifndef _PCI_I386_H_
 #define _PCI_I386_H_
 
+#include <pci.h>
+
+/* bus mapping constants (used for PCI core initialization) */
+#define PCI_REG_ADDR   0xcf8
+#define PCI_REG_DATA   0xcfc
+
+#define PCI_CFG_EN     0x80000000
+
+#ifndef __ASSEMBLY__
+
 #define DEFINE_PCI_DEVICE_TABLE(_table) \
        const struct pci_device_id _table[]
 
+struct pci_controller;
+
 void pci_setup_type1(struct pci_controller *hose);
-#endif
+
+/**
+ * board_pci_setup_hose() - Set up the PCI hose
+ *
+ * This is called by the common x86 PCI code to set up the PCI controller
+ * hose. It may be called when no memory/BSS is available so should just
+ * store things in 'hose' and not in BSS variables.
+ */
+void board_pci_setup_hose(struct pci_controller *hose);
+
+/**
+ * pci_early_init_hose() - Set up PCI host before relocation
+ *
+ * This allocates memory for, sets up and returns the PCI hose. It can be
+ * called before relocation. The hose will be stored in gd->hose for
+ * later use, but will become invalid one DRAM is available.
+ */
+int pci_early_init_hose(struct pci_controller **hosep);
+
+int board_pci_pre_scan(struct pci_controller *hose);
+int board_pci_post_scan(struct pci_controller *hose);
+
+/*
+ * Simple PCI access routines - these work from either the early PCI hose
+ * or the 'real' one, created after U-Boot has memory available
+ */
+unsigned int x86_pci_read_config8(pci_dev_t dev, unsigned where);
+unsigned int x86_pci_read_config16(pci_dev_t dev, unsigned where);
+unsigned int x86_pci_read_config32(pci_dev_t dev, unsigned where);
+
+void x86_pci_write_config8(pci_dev_t dev, unsigned where, unsigned value);
+void x86_pci_write_config16(pci_dev_t dev, unsigned where, unsigned value);
+void x86_pci_write_config32(pci_dev_t dev, unsigned where, unsigned value);
+
+int pci_x86_read_config(struct udevice *bus, pci_dev_t bdf, uint offset,
+                       ulong *valuep, enum pci_size_t size);
+
+int pci_x86_write_config(struct udevice *bus, pci_dev_t bdf, uint offset,
+                        ulong value, enum pci_size_t size);
+
+/**
+ * Assign IRQ number to a PCI device
+ *
+ * This function assigns IRQ for a PCI device. If the device does not exist
+ * or does not require interrupts then this function has no effect.
+ *
+ * @bus:       PCI bus number
+ * @device:    PCI device number
+ * @irq:       An array of IRQ numbers that are assigned to INTA through
+ *             INTD of this PCI device.
+ */
+void pci_assign_irqs(int bus, int device, u8 irq[4]);
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* _PCI_I386_H_ */