*/
#include <common.h>
+#include <asm/irq.h>
+#include <asm/pci.h>
#include <asm/post.h>
#include <asm/processor.h>
+#include <asm/arch/device.h>
+#include <asm/arch/qemu.h>
+#include <asm/fw_cfg.h>
+
+static bool i440fx;
+
+static void qemu_chipset_init(void)
+{
+ u16 device, xbcs;
+ int pam, i;
+
+ /*
+ * i440FX and Q35 chipset have different PAM register offset, but with
+ * the same bitfield layout. Here we determine the offset based on its
+ * PCI device ID.
+ */
+ device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
+ i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
+ pam = i440fx ? I440FX_PAM : Q35_PAM;
+
+ /*
+ * Initialize Programmable Attribute Map (PAM) Registers
+ *
+ * Configure legacy segments C/D/E/F to system RAM
+ */
+ for (i = 0; i < PAM_NUM; i++)
+ x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
+
+ if (i440fx) {
+ /*
+ * Enable legacy IDE I/O ports decode
+ *
+ * Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
+ * However Linux ata_piix driver does sanity check on these two
+ * registers to see whether legacy ports decode is turned on.
+ * This is to make Linux ata_piix driver happy.
+ */
+ x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
+ x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
+
+ /* Enable I/O APIC */
+ xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
+ xbcs |= APIC_EN;
+ x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
+ } else {
+ /* Configure PCIe ECAM base address */
+ x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
+ CONFIG_PCIE_ECAM_BASE | BAR_EN);
+ }
+
+ qemu_fwcfg_init();
+}
int arch_cpu_init(void)
{
int ret;
post_code(POST_CPU_INIT);
-#ifdef CONFIG_SYS_X86_TSC_TIMER
- timer_set_base(rdtsc());
-#endif
ret = x86_cpu_init_f();
if (ret)
return 0;
}
+#ifndef CONFIG_EFI_STUB
int print_cpuinfo(void)
{
post_code(POST_CPU_INFO);
return default_print_cpuinfo();
}
+#endif
void reset_cpu(ulong addr)
{
/* cold reset */
x86_full_reset();
}
+
+int arch_early_init_r(void)
+{
+ qemu_chipset_init();
+
+ return 0;
+}
+
+int arch_misc_init(void)
+{
+ return pirq_init();
+}
+
+#ifdef CONFIG_GENERATE_MP_TABLE
+int mp_determine_pci_dstirq(int bus, int dev, int func, int pirq)
+{
+ u8 irq;
+
+ if (i440fx) {
+ /*
+ * Not like most x86 platforms, the PIRQ[A-D] on PIIX3 are not
+ * connected to I/O APIC INTPIN#16-19. Instead they are routed
+ * to an irq number controled by the PIRQ routing register.
+ */
+ irq = x86_pci_read_config8(PCI_BDF(bus, dev, func),
+ PCI_INTERRUPT_LINE);
+ } else {
+ /*
+ * ICH9's PIRQ[A-H] are not consecutive numbers from 0 to 7.
+ * PIRQ[A-D] still maps to [0-3] but PIRQ[E-H] maps to [8-11].
+ */
+ irq = pirq < 8 ? pirq + 16 : pirq + 12;
+ }
+
+ return irq;
+}
+#endif