config SYS_ARCH
default "x86"
+choice
+ prompt "Run U-Boot in 32/64-bit mode"
+ default X86_RUN_32BIT
+ help
+ U-Boot can be built as a 32-bit binary which runs in 32-bit mode
+ even on 64-bit machines. In this case SPL is not used, and U-Boot
+ runs directly from the reset vector (via 16-bit start-up).
+
+ Alternatively it can be run as a 64-bit binary, thus requiring a
+ 64-bit machine. In this case SPL runs in 32-bit mode (via 16-bit
+ start-up) then jumps to U-Boot in 64-bit mode.
+
+ For now, 32-bit mode is recommended, as 64-bit is still
+ experimental and is missing a lot of features.
+
+config X86_RUN_32BIT
+ bool "32-bit"
+ help
+ Build U-Boot as a 32-bit binary with no SPL. This is the currently
+ supported normal setup. U-Boot will stay in 32-bit mode even on
+ 64-bit machines. When booting a 64-bit kernel, U-Boot will switch
+ to 64-bit just before starting the kernel. Only the bottom 4GB of
+ memory can be accessed through normal means, although
+ arch_phys_memset() can be used for basic access to other memory.
+
+config X86_RUN_64BIT
+ bool "64-bit"
+ select X86_64
+ select SUPPORT_SPL
+ select SPL
+ select SPL_SEPARATE_BSS
+ help
+ Build U-Boot as a 64-bit binary with a 32-bit SPL. This is
+ experimental and many features are missing. U-Boot SPL starts up,
+ runs through the 16-bit and 32-bit init, then switches to 64-bit
+ mode and jumps to U-Boot proper.
+
+endchoice
+
+config X86_64
+ bool
+
+config SPL_X86_64
+ bool
+ depends on SPL
+
choice
prompt "Mainboard vendor"
default VENDOR_EMULATION
endchoice
+# subarchitectures-specific options below
+config INTEL_MID
+ bool "Intel MID platform support"
+ select REGMAP
+ select SYSCON
+ help
+ Select to build a U-Boot capable of supporting Intel MID
+ (Mobile Internet Device) platform systems which do not have
+ the PCI legacy interfaces.
+
+ If you are building for a PC class system say N here.
+
+ Intel MID platforms are based on an Intel processor and
+ chipset which consume less power than most of the x86
+ derivatives.
+
# board-specific options below
source "board/advantech/Kconfig"
source "board/congatec/Kconfig"
bool
default n
+# The following options control where the 16-bit and 32-bit init lies
+# If SPL is enabled then it normally holds this init code, and U-Boot proper
+# is normally a 64-bit build.
+#
+# The 16-bit init refers to the reset vector and the small amount of code to
+# get the processor into 32-bit mode. It may be in SPL or in U-Boot proper,
+# or missing altogether if U-Boot is started from EFI or coreboot.
+#
+# The 32-bit init refers to processor init, running binary blobs including
+# FSP, setting up interrupts and anything else that needs to be done in
+# 32-bit code. It is normally in the same place as 16-bit init if that is
+# enabled (i.e. they are both in SPL, or both in U-Boot proper).
+config X86_16BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && !SPL
+ help
+ This is enabled when 16-bit init is in U-Boot proper
+
+config SPL_X86_16BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && SPL
+ help
+ This is enabled when 16-bit init is in SPL
+
+config X86_32BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && !SPL
+ help
+ This is enabled when 32-bit init is in U-Boot proper
+
+config SPL_X86_32BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && SPL
+ help
+ This is enabled when 32-bit init is in SPL
+
config RESET_SEG_START
hex
depends on X86_RESET_VECTOR
depends on X86_RESET_VECTOR
default 0xfffff800
+config X86_LOAD_FROM_32_BIT
+ bool "Boot from a 32-bit program"
+ help
+ Define this to boot U-Boot from a 32-bit program which sets
+ the GDT differently. This can be used to boot directly from
+ any stage of coreboot, for example, bypassing the normal
+ payload-loading feature.
+
config BOARD_ROMSIZE_KB_512
bool
config BOARD_ROMSIZE_KB_1024
to work correctly. It is not exhaustive but can save time by
detecting obvious failures.
+config FLASH_DESCRIPTOR_FILE
+ string "Flash descriptor binary filename"
+ depends on HAVE_INTEL_ME
+ default "descriptor.bin"
+ help
+ The filename of the file to use as flash descriptor in the
+ board directory.
+
+config INTEL_ME_FILE
+ string "Intel Management Engine binary filename"
+ depends on HAVE_INTEL_ME
+ default "me.bin"
+ help
+ The filename of the file to use as Intel Management Engine in the
+ board directory.
+
config HAVE_FSP
bool "Add an Firmware Support Package binary"
depends on !EFI
by the operating system. It defines platform-independent interfaces
for configuration and power management monitoring.
-config GENERATE_SMBIOS_TABLE
- bool "Generate an SMBIOS (System Management BIOS) table"
- default y
- help
- The System Management BIOS (SMBIOS) specification addresses how
- motherboard and system vendors present management information about
- their products in a standard format by extending the BIOS interface
- on Intel architecture systems.
-
- Check http://www.dmtf.org/standards/smbios for details.
-
-config SMBIOS_MANUFACTURER
- string "SMBIOS Manufacturer"
- depends on GENERATE_SMBIOS_TABLE
- default SYS_VENDOR
- help
- The board manufacturer to store in SMBIOS structures.
- Change this to override the default one (CONFIG_SYS_VENDOR).
-
-config SMBIOS_PRODUCT_NAME
- string "SMBIOS Product Name"
- depends on GENERATE_SMBIOS_TABLE
- default SYS_BOARD
- help
- The product name to store in SMBIOS structures.
- Change this to override the default one (CONFIG_SYS_BOARD).
-
endmenu
config MAX_PIRQ_LINKS
Intel 8254 timer contains three counters which have fixed uses.
Include this to have U-Boot set up the timer correctly.
-config I8042_KEYB
- default y
-
config SEABIOS
bool "Support booting SeaBIOS"
help