config SYS_ARCH
default "x86"
+choice
+ prompt "Run U-Boot in 32/64-bit mode"
+ default X86_RUN_32BIT
+ help
+ U-Boot can be built as a 32-bit binary which runs in 32-bit mode
+ even on 64-bit machines. In this case SPL is not used, and U-Boot
+ runs directly from the reset vector (via 16-bit start-up).
+
+ Alternatively it can be run as a 64-bit binary, thus requiring a
+ 64-bit machine. In this case SPL runs in 32-bit mode (via 16-bit
+ start-up) then jumps to U-Boot in 64-bit mode.
+
+ For now, 32-bit mode is recommended, as 64-bit is still
+ experimental and is missing a lot of features.
+
+config X86_RUN_32BIT
+ bool "32-bit"
+ help
+ Build U-Boot as a 32-bit binary with no SPL. This is the currently
+ supported normal setup. U-Boot will stay in 32-bit mode even on
+ 64-bit machines. When booting a 64-bit kernel, U-Boot will switch
+ to 64-bit just before starting the kernel. Only the bottom 4GB of
+ memory can be accessed through normal means, although
+ arch_phys_memset() can be used for basic access to other memory.
+
+config X86_RUN_64BIT
+ bool "64-bit"
+ select X86_64
+ select SUPPORT_SPL
+ select SPL
+ select SPL_SEPARATE_BSS
+ help
+ Build U-Boot as a 64-bit binary with a 32-bit SPL. This is
+ experimental and many features are missing. U-Boot SPL starts up,
+ runs through the 16-bit and 32-bit init, then switches to 64-bit
+ mode and jumps to U-Boot proper.
+
+endchoice
+
+config X86_64
+ bool
+
+config SPL_X86_64
+ bool
+ depends on SPL
+
choice
prompt "Mainboard vendor"
default VENDOR_EMULATION
+config VENDOR_ADVANTECH
+ bool "advantech"
+
+config VENDOR_CONGATEC
+ bool "congatec"
+
config VENDOR_COREBOOT
bool "coreboot"
+config VENDOR_DFI
+ bool "dfi"
+
config VENDOR_EFI
bool "efi"
endchoice
+# subarchitectures-specific options below
+config INTEL_MID
+ bool "Intel MID platform support"
+ select REGMAP
+ select SYSCON
+ help
+ Select to build a U-Boot capable of supporting Intel MID
+ (Mobile Internet Device) platform systems which do not have
+ the PCI legacy interfaces.
+
+ If you are building for a PC class system say N here.
+
+ Intel MID platforms are based on an Intel processor and
+ chipset which consume less power than most of the x86
+ derivatives.
+
# board-specific options below
+source "board/advantech/Kconfig"
+source "board/congatec/Kconfig"
source "board/coreboot/Kconfig"
+source "board/dfi/Kconfig"
source "board/efi/Kconfig"
source "board/emulation/Kconfig"
source "board/google/Kconfig"
# platform-specific options below
source "arch/x86/cpu/baytrail/Kconfig"
+source "arch/x86/cpu/broadwell/Kconfig"
source "arch/x86/cpu/coreboot/Kconfig"
source "arch/x86/cpu/ivybridge/Kconfig"
source "arch/x86/cpu/qemu/Kconfig"
# architecture-specific options below
+config AHCI
+ default y
+
config SYS_MALLOC_F_LEN
default 0x800
bool
default n
+# The following options control where the 16-bit and 32-bit init lies
+# If SPL is enabled then it normally holds this init code, and U-Boot proper
+# is normally a 64-bit build.
+#
+# The 16-bit init refers to the reset vector and the small amount of code to
+# get the processor into 32-bit mode. It may be in SPL or in U-Boot proper,
+# or missing altogether if U-Boot is started from EFI or coreboot.
+#
+# The 32-bit init refers to processor init, running binary blobs including
+# FSP, setting up interrupts and anything else that needs to be done in
+# 32-bit code. It is normally in the same place as 16-bit init if that is
+# enabled (i.e. they are both in SPL, or both in U-Boot proper).
+config X86_16BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && !SPL
+ help
+ This is enabled when 16-bit init is in U-Boot proper
+
+config SPL_X86_16BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && SPL
+ help
+ This is enabled when 16-bit init is in SPL
+
+config X86_32BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && !SPL
+ help
+ This is enabled when 32-bit init is in U-Boot proper
+
+config SPL_X86_32BIT_INIT
+ bool
+ depends on X86_RESET_VECTOR
+ default y if X86_RESET_VECTOR && SPL
+ help
+ This is enabled when 32-bit init is in SPL
+
config RESET_SEG_START
hex
depends on X86_RESET_VECTOR
depends on X86_RESET_VECTOR
default 0xfffff800
-config DM_PCI_COMPAT
- default y # Until we finish moving over to the new API
+config X86_LOAD_FROM_32_BIT
+ bool "Boot from a 32-bit program"
+ help
+ Define this to boot U-Boot from a 32-bit program which sets
+ the GDT differently. This can be used to boot directly from
+ any stage of coreboot, for example, bypassing the normal
+ payload-loading feature.
config BOARD_ROMSIZE_KB_512
bool
to work correctly. It is not exhaustive but can save time by
detecting obvious failures.
+config FLASH_DESCRIPTOR_FILE
+ string "Flash descriptor binary filename"
+ depends on HAVE_INTEL_ME
+ default "descriptor.bin"
+ help
+ The filename of the file to use as flash descriptor in the
+ board directory.
+
+config INTEL_ME_FILE
+ string "Intel Management Engine binary filename"
+ depends on HAVE_INTEL_ME
+ default "me.bin"
+ help
+ The filename of the file to use as Intel Management Engine in the
+ board directory.
+
config HAVE_FSP
bool "Add an Firmware Support Package binary"
depends on !EFI
are still some FSPs that might not even have UPD. For such FSPs,
override this to n in their platform Kconfig files.
+config FSP_BROKEN_HOB
+ bool
+ depends on HAVE_FSP
+ help
+ Indicate some buggy FSPs that does not report memory used by FSP
+ itself as reserved in the resource descriptor HOB. Select this to
+ tell U-Boot to do some additional work to ensure U-Boot relocation
+ do not overwrite the important boot service data which is used by
+ FSP, otherwise the subsequent call to fsp_notify() will fail.
+
config ENABLE_MRC_CACHE
bool "Enable MRC cache"
depends on !EFI && !SYS_COREBOOT
to be used for speeding up boot time on future reboots and/or
power cycles.
+ For platforms that use Intel FSP for the memory initialization,
+ please check FSP output HOB via U-Boot command 'fsp hob' to see
+ if there is FSP_NON_VOLATILE_STORAGE_HOB_GUID (asm/fsp/fsp_hob.h).
+ If such GUID does not exist, MRC cache is not avaiable on such
+ platform (eg: Intel Queensbay), which means selecting this option
+ here does not make any difference.
+
+config HAVE_MRC
+ bool "Add a System Agent binary"
+ depends on !HAVE_FSP
+ help
+ Select this option to add a System Agent binary to
+ the resulting U-Boot image. MRC stands for Memory Reference Code.
+ It is a binary blob which U-Boot uses to set up SDRAM.
+
+ Note: Without this binary U-Boot will not be able to set up its
+ SDRAM so will not boot.
+
+config CACHE_MRC_BIN
+ bool
+ depends on HAVE_MRC
+ default n
+ help
+ Enable caching for the memory reference code binary. This uses an
+ MTRR (memory type range register) to turn on caching for the section
+ of SPI flash that contains the memory reference code. This makes
+ SDRAM init run faster.
+
+config CACHE_MRC_SIZE_KB
+ int
+ depends on HAVE_MRC
+ default 512
+ help
+ Sets the size of the cached area for the memory reference code.
+ This ends at the end of SPI flash (address 0xffffffff) and is
+ measured in KB. Typically this is set to 512, providing for 0.5MB
+ of cached space.
+
+config DCACHE_RAM_BASE
+ hex
+ depends on HAVE_MRC
+ help
+ Sets the base of the data cache area in memory space. This is the
+ start address of the cache-as-RAM (CAR) area and the address varies
+ depending on the CPU. Once CAR is set up, read/write memory becomes
+ available at this address and can be used temporarily until SDRAM
+ is working.
+
+config DCACHE_RAM_SIZE
+ hex
+ depends on HAVE_MRC
+ default 0x40000
+ help
+ Sets the total size of the data cache area in memory space. This
+ sets the size of the cache-as-RAM (CAR) area. Note that much of the
+ CAR space is required by the MRC. The CAR space available to U-Boot
+ is normally at the start and typically extends to 1/4 or 1/2 of the
+ available size.
+
+config DCACHE_RAM_MRC_VAR_SIZE
+ hex
+ depends on HAVE_MRC
+ help
+ This is the amount of CAR (Cache as RAM) reserved for use by the
+ memory reference code. This depends on the implementation of the
+ memory reference code and must be set correctly or the board will
+ not boot.
+
+config HAVE_REFCODE
+ bool "Add a Reference Code binary"
+ help
+ Select this option to add a Reference Code binary to the resulting
+ U-Boot image. This is an Intel binary blob that handles system
+ initialisation, in this case the PCH and System Agent.
+
+ Note: Without this binary (on platforms that need it such as
+ broadwell) U-Boot will be missing some critical setup steps.
+ Various peripherals may fail to work.
+
config SMP
bool "Enable Symmetric Multiprocessing"
default n
config GENERATE_ACPI_TABLE
bool "Generate an ACPI (Advanced Configuration and Power Interface) table"
default n
+ select QFW if QEMU
help
The Advanced Configuration and Power Interface (ACPI) specification
provides an open standard for device configuration and management
by the operating system. It defines platform-independent interfaces
for configuration and power management monitoring.
-config GENERATE_SMBIOS_TABLE
- bool "Generate an SMBIOS (System Management BIOS) table"
- default y
+endmenu
+
+config HAVE_ACPI_RESUME
+ bool "Enable ACPI S3 resume"
help
- The System Management BIOS (SMBIOS) specification addresses how
- motherboard and system vendors present management information about
- their products in a standard format by extending the BIOS interface
- on Intel architecture systems.
+ Select this to enable ACPI S3 resume. S3 is an ACPI-defined sleeping
+ state where all system context is lost except system memory. U-Boot
+ is responsible for restoring the machine state as it was before sleep.
+ It needs restore the memory controller, without overwriting memory
+ which is not marked as reserved. For the peripherals which lose their
+ registers, U-Boot needs to write the original value. When everything
+ is done, U-Boot needs to find out the wakeup vector provided by OSes
+ and jump there.
- Check http://www.dmtf.org/standards/smbios for details.
+config S3_VGA_ROM_RUN
+ bool "Re-run VGA option ROMs on S3 resume"
+ depends on HAVE_ACPI_RESUME
+ default y if HAVE_ACPI_RESUME
+ help
+ Execute VGA option ROMs in U-Boot when resuming from S3. Normally
+ this is needed when graphics console is being used in the kernel.
-endmenu
+ Turning it off can reduce some resume time, but be aware that your
+ graphics console won't work without VGA options ROMs. Set it to N
+ if your kernel is only on a serial console.
+
+config STACK_SIZE
+ hex
+ depends on HAVE_ACPI_RESUME
+ default 0x1000
+ help
+ Estimated U-Boot's runtime stack size that needs to be reserved
+ during an ACPI S3 resume.
config MAX_PIRQ_LINKS
int
Intel 8254 timer contains three counters which have fixed uses.
Include this to have U-Boot set up the timer correctly.
-config I8042_KEYB
- default y
+config SEABIOS
+ bool "Support booting SeaBIOS"
+ help
+ SeaBIOS is an open source implementation of a 16-bit X86 BIOS.
+ It can run in an emulator or natively on X86 hardware with the use
+ of coreboot/U-Boot. By turning on this option, U-Boot prepares
+ all the configuration tables that are necessary to boot SeaBIOS.
-config DM_KEYBOARD
- default y
+ Check http://www.seabios.org/SeaBIOS for details.
+
+config HIGH_TABLE_SIZE
+ hex "Size of configuration tables which reside in high memory"
+ default 0x10000
+ depends on SEABIOS
+ help
+ SeaBIOS itself resides in E seg and F seg, where U-Boot puts all
+ configuration tables like PIRQ/MP/ACPI. To avoid conflicts, U-Boot
+ puts a copy of configuration tables in high memory region which
+ is reserved on the stack before relocation. The region size is
+ determined by this option.
+
+ Increse it if the default size does not fit the board's needs.
+ This is most likely due to a large ACPI DSDT table is used.
source "arch/x86/lib/efi/Kconfig"
projects / oweals / u-boot.git / blobdiff