* (C) Copyright 2000-2007
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
+ * SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#endif
}
+#ifdef CONFIG_SYS_4xx_CHIP_21_ERRATA
+void
+chip_21_errata(void)
+{
+ /*
+ * See rev 1.09 of the 405EX/405EXr errata. CHIP_21 says that
+ * sometimes reading the PVR and/or SDR0_ECID results in incorrect
+ * values. Since the rev-D chip uses the SDR0_ECID bits to control
+ * internal features, that means the second PCIe or ethernet of an EX
+ * variant could fail to work. Also, security features of both EX and
+ * EXr might be incorrectly disabled.
+ *
+ * The suggested workaround is as follows (covering rev-C and rev-D):
+ *
+ * 1.Read the PVR and SDR0_ECID3.
+ *
+ * 2.If the PVR matches an expected Revision C PVR value AND if
+ * SDR0_ECID3[12:15] is different from PVR[28:31], then processor is
+ * Revision C: continue executing the initialization code (no reset
+ * required). else go to step 3.
+ *
+ * 3.If the PVR matches an expected Revision D PVR value AND if
+ * SDR0_ECID3[10:11] matches its expected value, then continue
+ * executing initialization code, no reset required. else write
+ * DBCR0[RST] = 0b11 to generate a SysReset.
+ */
+
+ u32 pvr;
+ u32 pvr_28_31;
+ u32 ecid3;
+ u32 ecid3_10_11;
+ u32 ecid3_12_15;
+
+ /* Step 1: */
+ pvr = get_pvr();
+ mfsdr(SDR0_ECID3, ecid3);
+
+ /* Step 2: */
+ pvr_28_31 = pvr & 0xf;
+ ecid3_10_11 = (ecid3 >> 20) & 0x3;
+ ecid3_12_15 = (ecid3 >> 16) & 0xf;
+ if ((pvr == CONFIG_405EX_CHIP21_PVR_REV_C) &&
+ (pvr_28_31 != ecid3_12_15)) {
+ /* No reset required. */
+ return;
+ }
+
+ /* Step 3: */
+ if ((pvr == CONFIG_405EX_CHIP21_PVR_REV_D) &&
+ (ecid3_10_11 == CONFIG_405EX_CHIP21_ECID3_REV_D)) {
+ /* No reset required. */
+ return;
+ }
+
+ /* Reset required. */
+ __asm__ __volatile__ ("sync; isync");
+ mtspr(SPRN_DBCR0, 0x30000000);
+}
+#endif
+
/*
* Breath some life into the CPU...
*
u32 val;
#endif
+#ifdef CONFIG_SYS_4xx_CHIP_21_ERRATA
+ chip_21_errata();
+#endif
+
reconfigure_pll(CONFIG_SYS_PLL_RECONFIG);
-#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && !defined(CONFIG_SYS_4xx_GPIO_TABLE)
+#if (defined(CONFIG_405EP) || defined (CONFIG_405EX)) && \
+ !defined(CONFIG_APM821XX) &&!defined(CONFIG_SYS_4xx_GPIO_TABLE)
/*
* GPIO0 setup (select GPIO or alternate function)
*/
/*
* Set EMAC noise filter bits
*/
- mtdcr(CPC0_EPCTL, CPC0_EPRCSR_E0NFE | CPC0_EPRCSR_E1NFE);
+ mtdcr(CPC0_EPCTL, CPC0_EPCTL_E0NFE | CPC0_EPCTL_E1NFE);
#endif /* CONFIG_405EP */
#if defined(CONFIG_SYS_4xx_GPIO_TABLE)
* External Bus Controller (EBC) Setup
*/
#if (defined(CONFIG_SYS_EBC_PB0AP) && defined(CONFIG_SYS_EBC_PB0CR))
-#if (defined(CONFIG_405GP) || defined(CONFIG_405CR) || \
+#if (defined(CONFIG_405GP) || \
defined(CONFIG_405EP) || defined(CONFIG_405EZ) || \
defined(CONFIG_405EX) || defined(CONFIG_405))
/*
#endif
#if defined(CONFIG_WATCHDOG)
- val = mfspr(tcr);
+ val = mfspr(SPRN_TCR);
#if defined(CONFIG_440EP) || defined(CONFIG_440GR)
val |= 0xb8000000; /* generate system reset after 1.34 seconds */
#elif defined(CONFIG_440EPX)
val &= ~0x30000000; /* clear WRC bits */
val |= CONFIG_SYS_4xx_RESET_TYPE << 28; /* set board specific WRC type */
#endif
- mtspr(tcr, val);
+ mtspr(SPRN_TCR, val);
- val = mfspr(tsr);
+ val = mfspr(SPRN_TSR);
val |= 0x80000000; /* enable watchdog timer */
- mtspr(tsr, val);
+ mtspr(SPRN_TSR, val);
reset_4xx_watchdog();
#endif /* CONFIG_WATCHDOG */
#if defined(CONFIG_405EX) || \
defined(CONFIG_440SP) || defined(CONFIG_440SPE) || \
defined(CONFIG_460EX) || defined(CONFIG_460GT) || \
- defined(CONFIG_460SX)
+ defined(CONFIG_460SX) || defined(CONFIG_APM821XX)
/*
* Set PLB4 arbiter (Segment 0 and 1) to 4 deep pipeline read
*/