* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
- * You should have received a copy of the GNU General Public
- * License along with this file; if not, write to the Free
- * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- * MA 02110-1301 USA
- *
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
/dts-v1/;
#include "sun9i-a80.dtsi"
-#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
- pinctrl-0 = <&led_pins_optimus>;
+ pinctrl-0 = <&led_pins_optimus>, <&led_r_pins_optimus>;
/* The LED names match those found on the board */
gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>;
};
- /* led3 is on PM15, in R_PIO */
+ led3 {
+ label = "optimus:led3:usr";
+ gpios = <&r_pio 1 15 GPIO_ACTIVE_HIGH>; /* PM15 */
+ };
led4 {
label = "optimus:led4:usr";
};
};
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb1_vbus_pin_optimus>;
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+ };
+
reg_usb3_vbus: usb3-vbus {
compatible = "regulator-fixed";
pinctrl-names = "default";
status = "okay";
};
-&i2c3 {
+&mmc0 {
pinctrl-names = "default";
- pinctrl-0 = <&i2c3_pins_a>;
+ pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
+ cd-inverted;
status = "okay";
};
-&i2c3_pins_a {
- /* Enable internal pull-up */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
};
&ohci0 {
};
};
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>, <&mmc0_cd_pin_optimus>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <4>;
- cd-gpios = <&pio 7 18 GPIO_ACTIVE_HIGH>; /* PH8 */
- cd-inverted;
+&r_ir {
status = "okay";
};
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
- bus-width = <8>;
- non-removable;
- status = "okay";
+&r_pio {
+ led_r_pins_optimus: led-pins@1 {
+ allwinner,pins = "PM15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
-®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_optimus>;
- gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
+&r_rsb {
status = "okay";
+
+ axp809: pmic@3a3 {
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ /*
+ * TODO: This should be handled by the
+ * USB PHY driver.
+ */
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc33-usbh";
+ };
+
+ reg_aldo2: aldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pb-io-cam";
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_dc5ldo: dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus-09-usbh";
+ };
+
+ reg_dcdc1: dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v";
+ };
+
+ reg_dcdc2: dcdc2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-gpu";
+ };
+
+ reg_dcdc3: dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpua";
+ };
+
+ reg_dcdc4: dcdc4 {
+ regulator-always-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys-usb0-hdmi";
+ };
+
+ reg_dcdc5: dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1425000>;
+ regulator-max-microvolt = <1575000>;
+ regulator-name = "vcc-dram";
+ };
+
+ reg_dldo1: dldo1 {
+ /*
+ * The WiFi chip supports a wide range
+ * (3.0 ~ 4.8V) of voltages, and so does
+ * this regulator (3.0 ~ 4.2V), but
+ * Allwinner SDK always sets it to 3.3V.
+ */
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+ };
+
+ reg_dldo2: dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pl";
+ };
+
+ reg_eldo1: eldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-dvdd-cam";
+ };
+
+ reg_eldo2: eldo2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc-pe";
+ };
+
+ reg_eldo3: eldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pm-codec-io1";
+ };
+
+ reg_ldo_io0: ldo_io0 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pg";
+ };
+
+ reg_ldo_io1: ldo_io1 {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vcc-pa-gmac-2v5";
+ };
+
+ reg_rtc_ldo: rtc_ldo {
+ regulator-name = "vcc-rtc-vdd1v8-io";
+ };
+ };
+ };
};
+#include "axp809.dtsi"
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_a>;
- status = "okay";
-};
-
-&uart4_pins_a {
- /* Enable internal pull-up */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-};
-
&usbphy1 {
phy-supply = <®_usb1_vbus>;
status = "okay";
projects / oweals / u-boot.git / blobdiff