* OTHER DEALINGS IN THE SOFTWARE.
*/
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+/* The Orange Pi Plus is an extended version of the Orange Pi 2 */
+#include "sun8i-h3-orangepi-2.dts"
/ {
- model = "Xunlong Orange Pi Plus";
+ model = "Xunlong Orange Pi Plus / Plus 2";
compatible = "xunlong,orangepi-plus", "allwinner,sun8i-h3";
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_orangepi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
};
reg_usb3_vbus: usb3-vbus {
};
};
-&ehci1 {
- status = "okay";
-};
-
&ehci3 {
status = "okay";
};
-&pio {
- usb3_vbus_pin_a: usb3_vbus_pin@0 {
- allwinner,pins = "PG11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+&emac {
+ /* The Orange Pi Plus uses an external phy */
+ pinctrl-names = "default";
+ pinctrl-0 = <&emac_rgmii_pins>;
+ phy-supply = <®_gmac_3v3>;
+ phy-mode = "rgmii";
+ /delete-property/allwinner,use-internal-phy;
};
-&mmc0 {
+&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ pinctrl-0 = <&mmc2_8bit_pins>;
vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
status = "okay";
};
-®_usb1_vbus {
- gpio = <&pio 6 13 GPIO_ACTIVE_HIGH>;
- status = "okay";
+&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
+ /* eMMC is missing pull-ups */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
+&pio {
+ gmac_power_pin_orangepi: gmac_power_pin@0 {
+ allwinner,pins = "PD6";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
-&usb1_vbus_pin_a {
- allwinner,pins = "PG13";
+ usb3_vbus_pin_a: usb3_vbus_pin@0 {
+ allwinner,pins = "PG11";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&usbphy {
- usb1_vbus-supply = <®_usb1_vbus>;
usb3_vbus-supply = <®_usb3_vbus>;
- status = "okay";
};