chosen {
stdout-path = "serial0:115200n8";
};
+
+ panel {
+ compatible = "netron-dy,e231732";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ panel_input: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tcon0_out_panel>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc3>;
};
&ehci0 {
};
&lradc {
- vref-supply = <®_vcc3v0>;
+ vref-supply = <®_dcdc1>;
status = "okay";
button@200 {
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <4>;
cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
cd-inverted;
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <®_vcc3v0>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
+ cap-mmc-hw-reset;
status = "okay";
};
&mmc2_8bit_pins {
+ /* Increase drive strength for DDR modes */
+ allwinner,drive = <SUN4I_PINCTRL_40_MA>;
/* eMMC is missing pull-ups */
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
};
};
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&tcon0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_rgb666_pins>;
+ status = "okay";
+};
+
+&tcon0_out {
+ tcon0_out_panel: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_b>;
status = "okay";
};
+&usb_otg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
&usbphy {
status = "okay";
usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */