ARM: DTS: Re-sync logicpd-som-lv with Linux 4.16-rc3

[oweals/u-boot.git] / arch / arm / dts / sun8i-a33-sinlinx-sina33.dts

diff --git a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
index 1d5390d4e03aadd44965918d43c0672c070de9f9..b1bc88c46c672b757f59f827f1b6aac4ceb91ca4 100644 (file)
--- a/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
+++ b/arch/arm/dts/sun8i-a33-sinlinx-sina33.dts
@@ -61,6 +61,31 @@
        chosen {
                stdout-path = "serial0:115200n8";
        };
+
+       panel {
+               compatible = "netron-dy,e231732";
+               #address-cells = <1>;
+               #size-cells = <0>;
+
+               port@0 {
+                       reg = <0>;
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       panel_input: endpoint@0 {
+                               reg = <0>;
+                               remote-endpoint = <&tcon0_out_panel>;
+                       };
+               };
+       };
+};
+
+&de {
+       status = "okay";
+};
+
+&cpu0 {
+       cpu-supply = <&reg_dcdc3>;
 };
 
 &ehci0 {
@@ -68,7 +93,7 @@
 };
 
 &lradc {
-       vref-supply = <&reg_vcc3v0>;
+       vref-supply = <&reg_dcdc1>;
        status = "okay";
 
        button@200 {
@@ -96,7 +121,7 @@
 &mmc0 {
        pinctrl-names = "default";
        pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_sina33>;
-       vmmc-supply = <&reg_vcc3v0>;
+       vmmc-supply = <&reg_dcdc1>;
        bus-width = <4>;
        cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
        cd-inverted;
@@ -106,13 +131,16 @@
 &mmc2 {
        pinctrl-names = "default";
        pinctrl-0 = <&mmc2_8bit_pins>;
-       vmmc-supply = <&reg_vcc3v0>;
+       vmmc-supply = <&reg_dcdc1>;
        bus-width = <8>;
        non-removable;
+       cap-mmc-hw-reset;
        status = "okay";
 };
 
 &mmc2_8bit_pins {
+       /* Increase drive strength for DDR modes */
+       allwinner,drive = <SUN4I_PINCTRL_40_MA>;
        /* eMMC is missing pull-ups */
        allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 };
@@ -130,12 +158,104 @@
        };
 };
 
+&r_rsb {
+       status = "okay";
+
+       axp22x: pmic@3a3 {
+               compatible = "x-powers,axp223";
+               reg = <0x3a3>;
+               interrupt-parent = <&nmi_intc>;
+               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               eldoin-supply = <&reg_dcdc1>;
+       };
+};
+
+#include "axp22x.dtsi"
+
+&reg_aldo1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+       regulator-always-on;
+       regulator-min-microvolt = <2350000>;
+       regulator-max-microvolt = <2650000>;
+       regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+       regulator-always-on;
+       regulator-min-microvolt = <2700000>;
+       regulator-max-microvolt = <3300000>;
+       regulator-name = "vcc-pll-avcc";
+};
+
+&reg_dc5ldo {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+       regulator-always-on;
+       regulator-min-microvolt = <3000000>;
+       regulator-max-microvolt = <3000000>;
+       regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+       regulator-always-on;
+       regulator-min-microvolt = <900000>;
+       regulator-max-microvolt = <1400000>;
+       regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+       regulator-always-on;
+       regulator-min-microvolt = <1500000>;
+       regulator-max-microvolt = <1500000>;
+       regulator-name = "vcc-dram";
+};
+
+&reg_rtc_ldo {
+       regulator-name = "vcc-rtc";
+};
+
+&tcon0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&lcd_rgb666_pins>;
+       status = "okay";
+};
+
+&tcon0_out {
+       tcon0_out_panel: endpoint@0 {
+               reg = <0>;
+               remote-endpoint = <&panel_input>;
+       };
+};
+
 &uart0 {
        pinctrl-names = "default";
        pinctrl-0 = <&uart0_pins_b>;
        status = "okay";
 };
 
+&usb_otg {
+       dr_mode = "peripheral";
+       status = "okay";
+};
+
 &usbphy {
        status = "okay";
        usb1_vbus-supply = <&reg_vcc5v0>; /* USB1 VBUS is always on */