ARM: dts: stm32mp15: use DDR3 files generated by STM32CubeMX

[oweals/u-boot.git] / arch / arm / dts / sun7i-a20-pcduino3-nano.dts

diff --git a/arch/arm/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/dts/sun7i-a20-pcduino3-nano.dts
index ddac7328b852c1593fd269eca8c74ba8505a17fb..538ea15fa32fe981eb5be25727ac82a6babdb3e5 100644 (file)
--- a/arch/arm/dts/sun7i-a20-pcduino3-nano.dts
+++ b/arch/arm/dts/sun7i-a20-pcduino3-nano.dts
@@ -58,10 +58,19 @@
                stdout-path = "serial0:115200n8";
        };
 
+       hdmi-connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_con_in: endpoint {
+                               remote-endpoint = <&hdmi_out_con>;
+                       };
+               };
+       };
+
        leds {
                compatible = "gpio-leds";
-               pinctrl-names = "default";
-               pinctrl-0 = <&led_pins_pcduino3_nano>;
 
                /* Marked "LED3" on the PCB. */
                usr1 {
@@ -90,6 +99,10 @@
        cpu-supply = <&reg_dcdc2>;
 };
 
+&de {
+       status = "okay";
+};
+
 &ehci0 {
        status = "okay";
 };
@@ -100,7 +113,7 @@
 
 &gmac {
        pinctrl-names = "default";
-       pinctrl-0 = <&gmac_pins_rgmii_a>;
+       pinctrl-0 = <&gmac_rgmii_pins>;
        phy = <&phy1>;
        phy-mode = "rgmii";
        status = "okay";
@@ -110,9 +123,17 @@
        };
 };
 
+&hdmi {
+       status = "okay";
+};
+
+&hdmi_out {
+       hdmi_out_con: endpoint {
+               remote-endpoint = <&hdmi_con_in>;
+       };
+};
+
 &i2c0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&i2c0_pins_a>;
        status = "okay";
 
        axp209: pmic@34 {
@@ -124,17 +145,14 @@
 
 &ir0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&ir0_rx_pins_a>;
+       pinctrl-0 = <&ir0_rx_pin>;
        status = "okay";
 };
 
 &mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
        vmmc-supply = <&reg_vcc3v3>;
        bus-width = <4>;
-       cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-       cd-inverted;
+       cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
        status = "okay";
 };
 
@@ -151,37 +169,14 @@
 };
 
 &pio {
-       ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
-               allwinner,pins = "PH2";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       led_pins_pcduino3_nano: led_pins@0 {
-               allwinner,pins = "PH16", "PH15";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       usb0_id_detect_pin: usb0_id_detect_pin@0 {
-               allwinner,pins = "PH4";
-               allwinner,function = "gpio_in";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-       };
-
-       usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
-               allwinner,pins = "PD2";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       usb0_id_detect_pin: usb0-id-detect-pin {
+               pins = "PH4";
+               function = "gpio_in";
+               bias-pull-up;
        };
 };
 
 &reg_ahci_5v {
-       pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
        gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
        status = "okay";
 };
@@ -215,14 +210,13 @@
 
 /* A single regulator (U24) powers both USB host ports. */
 &reg_usb1_vbus {
-       pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
        gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
        status = "okay";
 };
 
 &uart0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
+       pinctrl-0 = <&uart0_pb_pins>;
        status = "okay";
 };