stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_pcduino3_nano>;
/* Marked "LED3" on the PCB. */
usr1 {
status = "okay";
};
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdc2>;
+};
+
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
&gmac {
pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
+ pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
phy-mode = "rgmii";
status = "okay";
};
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
- compatible = "x-powers,axp209";
reg = <0x34>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
};
};
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pin>;
status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- ahci_pwr_pin_pcduino3_nano: ahci_pwr_pin@0 {
- allwinner,pins = "PH2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- led_pins_pcduino3_nano: led_pins@0 {
- allwinner,pins = "PH16", "PH15";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+&otg_sram {
+ status = "okay";
+};
- usb1_vbus_pin_pcduino3_nano: usb1_vbus_pin@0 {
- allwinner,pins = "PH11";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+&pio {
+ usb0_id_detect_pin: usb0-id-detect-pin {
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
};
®_ahci_5v {
- pinctrl-0 = <&ahci_pwr_pin_pcduino3_nano>;
gpio = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
status = "okay";
};
-®_usb1_vbus {
- pinctrl-0 = <&usb1_vbus_pin_pcduino3_nano>;
- gpio = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
- status = "okay";
+#include "axp209.dtsi"
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-int-pll";
+};
+
+®_ldo1 {
+ regulator-name = "vdd-rtc";
+};
+
+®_ldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
};
-®_usb2_vbus {
+/* A single regulator (U24) powers both USB host ports. */
+®_usb1_vbus {
+ gpio = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
status = "okay";
};
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
status = "okay";
};
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
usb1_vbus-supply = <®_usb1_vbus>;
- usb2_vbus-supply = <®_usb2_vbus>;
+ usb2_vbus-supply = <®_usb1_vbus>;
status = "okay";
};