#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Lamobo R1";
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
};
};
-&ahci_pwr_pin_a {
- allwinner,pins = "PB3";
-};
-
&ahci {
target-supply = <®_ahci_5v>;
status = "okay";
cpu-supply = <®_dcdc2>;
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
reg = <8>;
label = "cpu";
ethernet = <&gmac>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-txid";
fixed-link {
speed = <1000>;
full-duplex;
};
};
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_lamobo_r1>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
- cd-inverted;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
status = "okay";
};
&pio {
usb0_id_detect_pin: usb0_id_detect_pin@0 {
- allwinner,pins = "PH4";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PH4";
+ function = "gpio_in";
+ bias-pull-up;
};
mmc0_cd_pin_lamobo_r1: mmc0_cd_pin@0 {
- allwinner,pins = "PH10";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ pins = "PH10";
+ function = "gpio_in";
+ bias-pull-up;
};
gmac_power_pin_lamobo_r1: gmac_power_pin@0 {
- allwinner,pins = "PH23";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PH23";
+ function = "gpio_out";
};
led_pins_lamobo_r1: led_pins@0 {
- allwinner,pins = "PH24";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ pins = "PH24";
+ function = "gpio_out";
};
};
#include "axp209.dtsi"
+&ac_power_supply {
+ status = "okay";
+};
+
+&battery_power_supply {
+ status = "okay";
+};
+
®_ahci_5v {
gpio = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
status = "okay";
status = "okay";
};
-&usb2_vbus_pin_a {
- allwinner,pins = "PH12";
-};
-
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>;