arm: dts: ls1088a: add external MDIO nodes

[oweals/u-boot.git] / arch / arm / dts / sun7i-a20-bananapro.dts

diff --git a/arch/arm/dts/sun7i-a20-bananapro.dts b/arch/arm/dts/sun7i-a20-bananapro.dts
index 18fcc87f462132366e1a3978118fb1800f9a46fc..0176e9de018033201cbf04b735d48a5530e9b22e 100644 (file)
--- a/arch/arm/dts/sun7i-a20-bananapro.dts
+++ b/arch/arm/dts/sun7i-a20-bananapro.dts
@@ -62,8 +62,6 @@
 
        leds {
                compatible = "gpio-leds";
-               pinctrl-names = "default";
-               pinctrl-0 = <&led_pins_bananapro>;
 
                blue {
                        label = "bananapro:blue:usr";
@@ -76,10 +74,13 @@
                };
        };
 
+       wifi_pwrseq: wifi-pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>;
+       };
+
        reg_gmac_3v3: gmac-3v3 {
                compatible = "regulator-fixed";
-               pinctrl-names = "default";
-               pinctrl-0 = <&gmac_power_pin_bananapro>;
                regulator-name = "gmac-3v3";
                regulator-min-microvolt = <3300000>;
                regulator-max-microvolt = <3300000>;
@@ -87,23 +88,16 @@
                enable-active-high;
                gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
        };
-
-       reg_vmmc3: vmmc3 {
-               compatible = "regulator-fixed";
-               pinctrl-names = "default";
-               pinctrl-0 = <&vmmc3_pin_bananapro>;
-               regulator-name = "vmmc3";
-               regulator-min-microvolt = <3300000>;
-               regulator-max-microvolt = <3300000>;
-               enable-active-high;
-               gpio = <&pio 7 22 GPIO_ACTIVE_HIGH>;
-       };
 };
 
 &ahci {
        status = "okay";
 };
 
+&codec {
+       status = "okay";
+};
+
 &ehci0 {
        status = "okay";
 };
@@ -114,7 +108,7 @@
 
 &gmac {
        pinctrl-names = "default";
-       pinctrl-0 = <&gmac_pins_rgmii_a>;
+       pinctrl-0 = <&gmac_rgmii_pins>;
        phy = <&phy1>;
        phy-mode = "rgmii";
        phy-supply = <&reg_gmac_3v3>;
@@ -126,8 +120,6 @@
 };
 
 &i2c0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&i2c0_pins_a>;
        status = "okay";
 
        axp209: pmic@34 {
@@ -142,34 +134,36 @@
 };
 
 &i2c2 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&i2c2_pins_a>;
        status = "okay";
 };
 
 &ir0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&ir0_rx_pins_a>;
+       pinctrl-0 = <&ir0_rx_pin>;
        status = "okay";
 };
 
 &mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapro>;
        vmmc-supply = <&reg_vcc3v3>;
        bus-width = <4>;
-       cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
-       cd-inverted;
+       cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
        status = "okay";
 };
 
 &mmc3 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc3_pins_a>;
-       vmmc-supply = <&reg_vmmc3>;
+       vmmc-supply = <&reg_vcc3v3>;
+       mmc-pwrseq = <&wifi_pwrseq>;
        bus-width = <4>;
        non-removable;
        status = "okay";
+
+       brcmf: wifi@1 {
+               reg = <1>;
+               compatible = "brcm,bcm4329-fmac";
+               interrupt-parent = <&pio>;
+               interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
+               interrupt-names = "host-wake";
+       };
 };
 
 &ohci0 {
@@ -180,85 +174,39 @@
        status = "okay";
 };
 
-&pio {
-       gmac_power_pin_bananapro: gmac_power_pin@0 {
-               allwinner,pins = "PH23";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       led_pins_bananapro: led_pins@0 {
-               allwinner,pins = "PH24", "PG2";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       mmc0_cd_pin_bananapro: mmc0_cd_pin@0 {
-               allwinner,pins = "PH10";
-               allwinner,function = "gpio_in";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
-       };
-
-       usb1_vbus_pin_bananapro: usb1_vbus_pin@0 {
-               allwinner,pins = "PH0";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       usb2_vbus_pin_bananapro: usb2_vbus_pin@0 {
-               allwinner,pins = "PH1";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-
-       vmmc3_pin_bananapro: vmmc3_pin@0 {
-               allwinner,pins = "PH22";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-       };
-};
-
 &reg_usb1_vbus {
-       pinctrl-0 = <&usb1_vbus_pin_bananapro>;
        gpio = <&pio 7 0 GPIO_ACTIVE_HIGH>; /* PH0 */
        status = "okay";
 };
 
 &reg_usb2_vbus {
-       pinctrl-0 = <&usb2_vbus_pin_bananapro>;
        gpio = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
        status = "okay";
 };
 
 &spi0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&spi0_pins_a>,
-                   <&spi0_cs0_pins_a>,
-                   <&spi0_cs1_pins_a>;
+       pinctrl-0 = <&spi0_pi_pins>,
+                   <&spi0_cs0_pi_pin>,
+                   <&spi0_cs1_pi_pin>;
        status = "okay";
 };
 
 &uart0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
+       pinctrl-0 = <&uart0_pb_pins>;
        status = "okay";
 };
 
 &uart4 {
        pinctrl-names = "default";
-       pinctrl-0 = <&uart4_pins_b>;
+       pinctrl-0 = <&uart4_ph_pins>;
        status = "okay";
 };
 
 &uart7 {
        pinctrl-names = "default";
-       pinctrl-0 = <&uart7_pins_a>;
+       pinctrl-0 = <&uart7_pi_pins>;
        status = "okay";
 };