#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
/ {
model = "Utoo P66";
compatible = "utoo,p66", "allwinner,sun5i-a13";
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ /* Note levels of 10 / 20% result in backlight off */
+ brightness-levels = <0 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <6>;
+ /* TODO: backlight uses axp gpio1 as enable pin */
+ };
+
i2c_lcd: i2c@0 {
/* The lcd panel i2c interface is hooked up via gpios */
compatible = "i2c-gpio";
};
};
+&codec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&codec_pa_pin>;
+ allwinner,pa-gpios = <&pio 6 3 GPIO_ACTIVE_HIGH>; /* PG3 */
+ status = "okay";
+};
+
&cpu0 {
cpu-supply = <®_dcdc2>;
};
compatible = "chipone,icn8318";
reg = <0x40>;
interrupt-parent = <&pio>;
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+ interrupts = <6 9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
pinctrl-names = "default";
pinctrl-0 = <&ts_wake_pin_p66>;
wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
};
};
+&otg_sram {
+ status = "okay";
+};
+
&pio {
+ codec_pa_pin: codec_pa_pin@0 {
+ allwinner,pins = "PG3";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
mmc0_cd_pin_p66: mmc0_cd_pin@0 {
allwinner,pins = "PG0";
allwinner,function = "gpio_in";
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
+ usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
+ allwinner,pins = "PG1";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PG2";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
i2c_lcd_pins: i2c_lcd_pin@0 {
allwinner,pins = "PG10", "PG12";
allwinner,function = "gpio_out";
};
};
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
®_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
status = "okay";
};
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
+ usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
+ usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_ldo3>;
status = "okay";