#include "sunxi-common-regulators.dtsi"
#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Jesurun Q5";
leds {
compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_q5>;
green {
label = "q5:green:usr";
reg_emac_3v3: emac-3v3 {
compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&emac_power_pin_q5>;
regulator-name = "emac-3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ startup-delay-us = <20000>;
enable-active-high;
gpio = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */
};
};
&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
axp209: pmic@34 {
&ir0 {
pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
+ pinctrl-0 = <&ir0_rx_pins>;
status = "okay";
};
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
- cd-inverted;
+ cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
status = "okay";
};
status = "okay";
};
-&pio {
- emac_power_pin_q5: emac_power_pin@0 {
- allwinner,pins = "PH19";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+&otg_sram {
+ status = "okay";
+};
- led_pins_q5: led_pins@0 {
- allwinner,pins = "PH20";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+®_usb0_vbus {
+ regulator-boot-on;
+ status = "okay";
};
®_usb1_vbus {
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "host";
status = "okay";
};
&usbphy {
+ usb0_vbus-supply = <®_usb0_vbus>;
usb1_vbus-supply = <®_usb1_vbus>;
usb2_vbus-supply = <®_usb2_vbus>;
status = "okay";