ARM: dts: rmobile: Add soc label to Gen3

[oweals/u-boot.git] / arch / arm / dts / sun4i-a10-cubieboard.dts

diff --git a/arch/arm/dts/sun4i-a10-cubieboard.dts b/arch/arm/dts/sun4i-a10-cubieboard.dts
index 9afb4e0185935ee4ffdda47e3595cc352341364a..197a1f2b75ff722bb7aa460eeaf5bf6f0c6d9d85 100644 (file)
--- a/arch/arm/dts/sun4i-a10-cubieboard.dts
+++ b/arch/arm/dts/sun4i-a10-cubieboard.dts
@@ -46,7 +46,6 @@
 #include "sunxi-common-regulators.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
 
 / {
        model = "Cubietech Cubieboard";
@@ -60,6 +59,17 @@
                stdout-path = "serial0:115200n8";
        };
 
+       hdmi-connector {
+               compatible = "hdmi-connector";
+               type = "a";
+
+               port {
+                       hdmi_con_in: endpoint {
+                               remote-endpoint = <&hdmi_out_con>;
+                       };
+               };
+       };
+
        leds {
                compatible = "gpio-leds";
                pinctrl-names = "default";
@@ -83,10 +93,18 @@
        status = "okay";
 };
 
+&codec {
+       status = "okay";
+};
+
 &cpu0 {
        cpu-supply = <&reg_dcdc2>;
 };
 
+&de {
+       status = "okay";
+};
+
 &ehci0 {
        status = "okay";
 };
@@ -96,8 +114,6 @@
 };
 
 &emac {
-       pinctrl-names = "default";
-       pinctrl-0 = <&emac_pins_a>;
        phy = <&phy1>;
        status = "okay";
 };
@@ -106,9 +122,17 @@
        status = "okay";
 };
 
+&hdmi {
+       status = "okay";
+};
+
+&hdmi_out {
+       hdmi_out_con: endpoint {
+               remote-endpoint = <&hdmi_con_in>;
+       };
+};
+
 &i2c0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&i2c0_pins_a>;
        status = "okay";
 
        axp209: pmic@34 {
@@ -118,14 +142,12 @@
 };
 
 &i2c1 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&i2c1_pins_a>;
        status = "okay";
 };
 
 &ir0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&ir0_rx_pins_a>;
+       pinctrl-0 = <&ir0_rx_pins>;
        status = "okay";
 };
 
@@ -138,12 +160,9 @@
 };
 
 &mmc0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>;
        vmmc-supply = <&reg_vcc3v3>;
        bus-width = <4>;
-       cd-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
-       cd-inverted;
+       cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
        status = "okay";
 };
 
@@ -155,12 +174,21 @@
        status = "okay";
 };
 
+&otg_sram {
+       status = "okay";
+};
+
 &pio {
-       led_pins_cubieboard: led_pins@0 {
-               allwinner,pins = "PH20", "PH21";
-               allwinner,function = "gpio_out";
-               allwinner,drive = <SUN4I_PINCTRL_20_MA>;
-               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+       led_pins_cubieboard: led-pins {
+               pins = "PH20", "PH21";
+               function = "gpio_out";
+               drive-strength = <20>;
+       };
+
+       usb0_id_detect_pin: usb0-id-detect-pin {
+               pins = "PH4";
+               function = "gpio_in";
+               bias-pull-up;
        };
 };
 
@@ -170,6 +198,10 @@
 
 #include "axp209.dtsi"
 
+&ac_power_supply {
+       status = "okay";
+};
+
 &reg_dcdc2 {
        regulator-always-on;
        regulator-min-microvolt = <1000000>;
@@ -205,18 +237,26 @@
 
 &spi0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&spi0_pins_a>,
-                   <&spi0_cs0_pins_a>;
+       pinctrl-0 = <&spi0_pi_pins>,
+                   <&spi0_cs0_pi_pin>;
        status = "okay";
 };
 
 &uart0 {
        pinctrl-names = "default";
-       pinctrl-0 = <&uart0_pins_a>;
+       pinctrl-0 = <&uart0_pb_pins>;
+       status = "okay";
+};
+
+&usb_otg {
+       dr_mode = "otg";
        status = "okay";
 };
 
 &usbphy {
+       pinctrl-names = "default";
+       pinctrl-0 = <&usb0_id_detect_pin>;
+       usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
        usb1_vbus-supply = <&reg_usb1_vbus>;
        usb2_vbus-supply = <&reg_usb2_vbus>;
        status = "okay";