* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
*/
-/dts-v1/;
-
-#include "stm32mp157c.dtsi"
-#include "stm32mp157xac-pinctrl.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-
-/ {
- model = "Arrow Electronics STM32MP157A Avenger96 board";
- compatible = "arrow,stm32mp157a-avenger96", "st,stm32mp157";
-
- aliases {
- eeprom0 = &eeprom0;
- ethernet0 = ðernet0;
- mmc0 = &sdmmc1;
- serial0 = &uart4;
- serial1 = &uart7;
- spi0 = &qspi;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- memory@c0000000 {
- device_type = "memory";
- reg = <0xc0000000 0x40000000>;
- };
-
- led {
- compatible = "gpio-leds";
- led1 {
- label = "green:user1";
- gpios = <&gpioz 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- led2 {
- label = "green:user2";
- gpios = <&gpiof 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- led3 {
- label = "green:user3";
- gpios = <&gpiog 0 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- led4 {
- label = "green:user3";
- gpios = <&gpiog 1 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- panic-indicator;
- };
-
- led5 {
- label = "yellow:wifi";
- gpios = <&gpioz 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tx";
- default-state = "off";
- };
-
- led6 {
- label = "blue:bt";
- gpios = <&gpioz 6 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "bluetooth-power";
- default-state = "off";
- };
- };
-
- sd_switch: regulator-sd_switch {
- compatible = "regulator-gpio";
- regulator-name = "sd_switch";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <2900000>;
- regulator-type = "voltage";
- regulator-always-on;
-
- gpios = <&gpioi 5 GPIO_ACTIVE_HIGH>;
- gpios-states = <0>;
- states = <1800000 0x1>,
- <2900000 0x0>;
- };
-
- /* Enpirion EP3A8LQI U2 on the DHCOR */
- vdd_io: regulator-buck-io {
- compatible = "regulator-fixed";
- regulator-name = "buck-io";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vdd>;
- };
-};
-
-ðernet0 {
- status = "okay";
- pinctrl-0 = <ðernet0_rgmii_pins_b>;
- pinctrl-1 = <ðernet0_rgmii_pins_sleep_b>;
- pinctrl-names = "default", "sleep";
- phy-mode = "rgmii";
- max-speed = <1000>;
- phy-handle = <&phy0>;
- phy-reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
-
- mdio0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "snps,dwmac-mdio";
- phy0: ethernet-phy@7 {
- reg = <7>;
- };
- };
-};
-
-&i2c1 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins_b>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c2 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins_b1 &i2c2_pins_b2>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-};
-
-&i2c4 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c4_pins_a>;
- i2c-scl-rising-time-ns = <185>;
- i2c-scl-falling-time-ns = <20>;
- status = "okay";
- /delete-property/dmas;
- /delete-property/dma-names;
-
- pmic: stpmic@33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- st,main-control-register = <0x04>;
- st,vin-control-register = <0xc0>;
- st,usb-control-register = <0x30>;
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo1-supply = <&v3v3>;
- ldo2-supply = <&v3v3>;
- ldo3-supply = <&vdd_ddr>;
- ldo5-supply = <&v3v3>;
- ldo6-supply = <&v3v3>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcore: buck1 {
- regulator-name = "vddcore";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 {
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 {
- regulator-name = "vdd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- regulator-always-on;
- st,mask_reset;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- v3v3: buck4 {
- regulator-name = "v3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-over-current-protection;
- regulator-initial-mode = <0>;
- };
-
- vdda: ldo1 {
- regulator-name = "vdda";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- interrupt-parent = <&pmic>;
- };
-
- v2v8: ldo2 {
- regulator-name = "v2v8";
- regulator-min-microvolt = <2800000>;
- regulator-max-microvolt = <2800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- interrupt-parent = <&pmic>;
- };
-
- vtt_ddr: ldo3 {
- regulator-name = "vtt_ddr";
- regulator-min-microvolt = <500000>;
- regulator-max-microvolt = <750000>;
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- vdd_usb: ldo4 {
- regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO4 0>;
- interrupt-parent = <&pmic>;
- };
-
- vdd_sd: ldo5 {
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <2900000>;
- regulator-max-microvolt = <2900000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- interrupt-parent = <&pmic>;
- regulator-boot-on;
- };
-
- v1v8: ldo6 {
- regulator-name = "v1v8";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- interrupt-parent = <&pmic>;
- regulator-enable-ramp-delay = <300000>;
- };
-
- vref_ddr: vref_ddr {
- regulator-name = "vref_ddr";
- regulator-always-on;
- regulator-over-current-protection;
- };
-
- bst_out: boost {
- regulator-name = "bst_out";
- interrupts = <IT_OCP_BOOST 0>;
- interrupt-parent = <&pmic>;
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- interrupt-parent = <&pmic>;
- regulator-active-discharge = <1>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- interrupt-parent = <&pmic>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- eeprom0: eeprom@53 {
- compatible = "atmel,24c02";
- reg = <0x53>;
- pagesize = <16>;
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&pwr_regulators {
- vdd-supply = <&vdd_io>;
- vdd_3v3_usbfs-supply = <&vdd_usb>;
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
- reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: spi-flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-&rng1 {
- status = "okay";
-};
-
-&rtc {
- status = "okay";
-};
-
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_b>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_b>;
- disable-wp;
- st,sig-dir;
- st,neg-edge;
- st,use-ckin;
- sd-uhs-sdr104;
- bus-width = <4>;
- vmmc-supply = <&vdd_sd>;
- vqmmc-supply = <&sd_switch>;
- status = "okay";
-};
-
-&sdmmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
- non-removable;
- no-sd;
- no-sdio;
- st,neg-edge;
- bus-width = <8>;
- vmmc-supply = <&v3v3>;
- mmc-ddr-3_3v;
- status = "okay";
-};
-
-&spi2 {
- pinctrl-names = "default";
- pinctrl-0 = <&spi2_pins_a>;
- status = "okay";
-};
-
-&uart4 {
- /* On Low speed expansion header */
- label = "LS-UART1";
- pinctrl-names = "default";
- pinctrl-0 = <&uart4_pins_b>;
- status = "okay";
-};
-
-&uart7 {
- /* On Low speed expansion header */
- label = "LS-UART0";
- pinctrl-names = "default";
- pinctrl-0 = <&uart7_pins_a>;
- status = "okay";
-};
-
-&usbh_ehci {
- phys = <&usbphyc_port0>;
- phy-names = "usb";
- status = "okay";
-};
-
-&usbotg_hs {
- dr_mode = "peripheral";
- phys = <&usbphyc_port1 0>;
- phy-names = "usb2-phy";
- status = "okay";
-};
-
-&usbphyc {
- status = "okay";
-};
-
-&usbphyc_port0 {
- phy-supply = <&vdd_usb>;
-};
-
-&usbphyc_port1 {
- phy-supply = <&vdd_usb>;
-};
+/* This is kept for backward compatibility and will be removed */
+#include "stm32mp15xx-dhcor-avenger96.dts"
projects / oweals / u-boot.git / blobdiff