/dts-v1/;
#include <dt-bindings/input/input.h>
-#include <dt-bindings/thermal/thermal.h>
#include "meson-gxm.dtsi"
aliases {
serial0 = &uart_AO;
- serial1 = &uart_A;
serial2 = &uart_AO_B;
};
gpio-keys-polled {
compatible = "gpio-keys-polled";
- #address-cells = <1>;
- #size-cells = <0>;
poll-interval = <100>;
- button@0 {
+ power-button {
label = "power";
linux,code = <KEY_POWER>;
gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
clock-names = "ext_clock";
};
- thermal-zones {
- cpu-thermal {
- polling-delay-passive = <250>; /* milliseconds */
- polling-delay = <1000>; /* milliseconds */
-
- thermal-sensors = <&scpi_sensors 0>;
-
- trips {
- cpu_alert0: cpu-alert0 {
- temperature = <70000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "active";
- };
-
- cpu_alert1: cpu-alert1 {
- temperature = <80000>; /* millicelsius */
- hysteresis = <2000>; /* millicelsius */
- type = "passive";
- };
- };
-
- cooling-maps {
- map0 {
- trip = <&cpu_alert0>;
- cooling-device = <&gpio_fan THERMAL_NO_LIMIT 1>;
- };
-
- map1 {
- trip = <&cpu_alert1>;
- cooling-device = <&gpio_fan 2 THERMAL_NO_LIMIT>;
- };
-
- map2 {
- trip = <&cpu_alert1>;
- cooling-device =
- <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
-
- map3 {
- trip = <&cpu_alert1>;
- cooling-device =
- <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
- };
- };
- };
- };
-
hdmi_5v: regulator-hdmi-5v {
compatible = "regulator-fixed";
hdmi-phandle = <&hdmi_tx>;
};
-&cpu0 {
- #cooling-cells = <2>;
-};
-
-&cpu1 {
- #cooling-cells = <2>;
-};
-
-&cpu2 {
- #cooling-cells = <2>;
-};
-
-&cpu3 {
- #cooling-cells = <2>;
-};
-
-&cpu4 {
- #cooling-cells = <2>;
-};
-
-&cpu5 {
- #cooling-cells = <2>;
-};
-&cpu6 {
- #cooling-cells = <2>;
-};
+&cpu_cooling_maps {
+ map0 {
+ cooling-device = <&gpio_fan THERMAL_NO_LIMIT 1>;
+ };
-&cpu7 {
- #cooling-cells = <2>;
+ map1 {
+ cooling-device = <&gpio_fan 2 THERMAL_NO_LIMIT>,
+ <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+ <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
};
ðmac {
amlogic,tx-delay-ns = <2>;
- /* External PHY reset is shared with internal PHY Led signals */
- snps,reset-gpio = <&gpio GPIOZ_14 0>;
- snps,reset-delays-us = <0 10000 1000000>;
- snps,reset-active-low;
-
/* External PHY is in RGMII */
phy-mode = "rgmii";
external_phy: ethernet-phy@0 {
/* Realtek RTL8211F (0x001cc916) */
reg = <0>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
interrupt-parent = <&gpio_intc>;
/* MAC_INTR on GPIOZ_15 */
interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
status = "okay";
pinctrl-0 = <&remote_input_ao_pins>;
pinctrl-names = "default";
- linux,rc-map-name = "rc-geekbox";
+ linux,rc-map-name = "rc-khadas";
};
&pwm_AO_ab {
&sd_emmc_a {
status = "okay";
pinctrl-0 = <&sdio_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdio_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
- max-frequency = <100000000>;
+ max-frequency = <60000000>;
non-removable;
disable-wp;
+ /* WiFi firmware requires power to be kept while in suspend */
+ keep-power-in-suspend;
+
mmc-pwrseq = <&sdio_pwrseq>;
vmmc-supply = <&vddao_3v3>;
&sd_emmc_b {
status = "okay";
pinctrl-0 = <&sdcard_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdcard_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <4>;
cap-sd-highspeed;
- max-frequency = <100000000>;
+ max-frequency = <50000000>;
disable-wp;
- cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
- cd-inverted;
+ cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_LOW>;
vmmc-supply = <&vddao_3v3>;
vqmmc-supply = <&vddio_boot>;
&sd_emmc_c {
status = "okay";
pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
bus-width = <8>;
- cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <200000000>;
non-removable;
disable-wp;
mmc-ddr-1_8v;
mmc-hs200-1_8v;
- mmc-hs400-1_8v;
mmc-pwrseq = <&emmc_pwrseq>;
vmmc-supply = <&vcc_3v3>;
/* This one is connected to the Bluetooth module */
&uart_A {
status = "okay";
- pinctrl-0 = <&uart_a_pins>;
+ pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
pinctrl-names = "default";
+ uart-has-rtscts;
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+ max-speed = <2000000>;
+ clocks = <&wifi32k>;
+ clock-names = "lpo";
+ };
};
/* This is brought out on the Linux_RX (18) and Linux_TX (19) pins: */