/dts-v1/;
#include "exynos54xx.dtsi"
+#include <dt-bindings/clock/maxim,max77802.h>
+#include <dt-bindings/regulator/maxim,max77802.h>
/ {
model = "Samsung/Google Peach Pit board based on Exynos5420";
i2c104 = &i2c_tunnel;
};
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm 0 1000000 0>;
+ brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
+ default-brightness-level = <7>;
+ power-supply = <&tps65090_fet1>;
+ };
+
dmc {
mem-manuf = "samsung";
mem-type = "ddr3";
compatible = "maxim,max98090-codec";
};
- edp-lvds-bridge@48 {
- compatible = "parade,ps8625";
- reg = <0x48>;
- sleep-gpio = <&gpx3 5 GPIO_ACTIVE_HIGH>;
- reset-gpio = <&gpy7 7 GPIO_ACTIVE_HIGH>;
+ edp-lvds-bridge@48 {
+ compatible = "parade,ps8625";
+ reg = <0x48>;
+ sleep-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpy7 7 GPIO_ACTIVE_LOW>;
+ parade,regs = /bits/ 8 <
+ 0x02 0xa1 0x01 /* HPD low */
+ /*
+ * SW setting
+ * [1:0] SW output 1.2V voltage is lower to 96%
+ */
+ 0x04 0x14 0x01
+ /*
+ * RCO SS setting
+ * [5:4] = b01 0.5%, b10 1%, b11 1.5%
+ */
+ 0x04 0xe3 0x20
+ 0x04 0xe2 0x80 /* [7] RCO SS enable */
+ /*
+ * RPHY Setting
+ * [3:2] CDR tune wait cycle before
+ * measure for fine tune b00: 1us,
+ * 01: 0.5us, 10:2us, 11:4us.
+ */
+ 0x04 0x8a 0x0c
+ 0x04 0x89 0x08 /* [3] RFD always on */
+ /*
+ * CTN lock in/out:
+ * 20000ppm/80000ppm. Lock out 2
+ * times.
+ */
+ 0x04 0x71 0x2d
+ /*
+ * 2.7G CDR settings
+ * NOF=40LSB for HBR CDR setting
+ */
+ 0x04 0x7d 0x07
+ 0x04 0x7b 0x00 /* [1:0] Fmin=+4bands */
+ 0x04 0x7a 0xfd /* [7:5] DCO_FTRNG=+-40% */
+ /*
+ * 1.62G CDR settings
+ * [5:2]NOF=64LSB [1:0]DCO scale is 2/5
+ */
+ 0x04 0xc0 0x12
+ 0x04 0xc1 0x92 /* Gitune=-37% */
+ 0x04 0xc2 0x1c /* Fbstep=100% */
+ 0x04 0x32 0x80 /* [7]LOS signal disable */
+ /*
+ * RPIO Setting
+ * [7:4] LVDS driver bias current :
+ * 75% (250mV swing)
+ */
+ 0x04 0x00 0xb0
+ /*
+ * [7:6] Right-bar GPIO output strength is 8mA
+ */
+ 0x04 0x15 0x40
+ /* EQ Training State Machine Setting */
+ 0x04 0x54 0x10 /* RCO calibration start */
+ /* [4:0] MAX_LANE_COUNT set to one lane */
+ 0x01 0x02 0x81
+ /* [4:0] LANE_COUNT_SET set to one lane */
+ 0x01 0x21 0x81
+ 0x00 0x52 0x20
+ 0x00 0xf1 0x03 /* HPD CP toggle enable */
+ 0x00 0x62 0x41
+ /* Counter number add 1ms counter delay */
+ 0x00 0xf6 0x01
+ /*
+ * [6]PWM function control by
+ * DPCD0040f[7], default is PWM
+ * block always works.
+ */
+ 0x00 0x77 0x06
+ /*
+ * 04h Adjust VTotal tolerance to
+ * fix the 30Hz no display issue
+ */
+ 0x00 0x4c 0x04
+ /* DPCD00400='h00, Parade OUI = 'h001cf8 */
+ 0x01 0xc0 0x00
+ 0x01 0xc1 0x1c /* DPCD00401='h1c */
+ 0x01 0xc2 0xf8 /* DPCD00402='hf8 */
+ /*
+ * DPCD403~408 = ASCII code
+ * D2SLV5='h4432534c5635
+ */
+ 0x01 0xc3 0x44
+ 0x01 0xc4 0x32 /* DPCD404 */
+ 0x01 0xc5 0x53 /* DPCD405 */
+ 0x01 0xc6 0x4c /* DPCD406 */
+ 0x01 0xc7 0x56 /* DPCD407 */
+ 0x01 0xc8 0x35 /* DPCD408 */
+ /*
+ * DPCD40A, Initial Code major revision
+ * '01'
+ */
+ 0x01 0xca 0x01
+ /* DPCD40B Initial Code minor revision '05' */
+ 0x01 0xcb 0x05
+ /* DPCD720 Select internal PWM */
+ 0x01 0xa5 0xa0
+ /*
+ * FFh for 100% PWM of brightness, 0h for 0%
+ * brightness
+ */
+ 0x01 0xa7 0xff
+ /*
+ * Set LVDS output as 6bit-VESA mapping,
+ * single LVDS channel
+ */
+ 0x01 0xcc 0x13
+ /* Enable SSC set by register */
+ 0x02 0xb1 0x20
+ /*
+ * Set SSC enabled and +/-1% central
+ * spreading
+ */
+ 0x04 0x10 0x16
+ /* MPU Clock source: LC => RCO */
+ 0x04 0x59 0x60
+ 0x04 0x54 0x14 /* LC -> RCO */
+ 0x02 0xa1 0x91>; /* HPD high */
+
+ ports {
+ port@0 {
+ bridge_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+
+ port@1 {
+ bridge_in: endpoint {
+ remote-endpoint = <&dp_out>;
+ };
+ };
+ };
};
};
i2c@12E10000 { /* i2c9 */
clock-frequency = <400000>;
- tpm@20 {
- compatible = "infineon,slb9645tt";
- reg = <0x20>;
+ tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+ };
+
+ panel: panel {
+ compatible = "auo,b116xw03";
+ power-supply = <&tps65090_fet6>;
+ backlight = <&backlight>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&bridge_out>;
+ };
};
};
};
};
+&dp {
+ status = "okay";
+ samsung,color-space = <0>;
+ samsung,dynamic-range = <0>;
+ samsung,ycbcr-coeff = <0>;
+ samsung,color-depth = <1>;
+ samsung,link-rate = <0x06>;
+ samsung,lane-count = <2>;
+ samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+
+ ports {
+ port@0 {
+ dp_out: endpoint {
+ remote-endpoint = <&bridge_in>;
+ };
+ };
+ };
+};
+
&spi_2 {
spi-max-frequency = <3125000>;
spi-deactivate-delay = <200>;
projects / oweals / u-boot.git / blobdiff