#include <asm/arch/sys_proto.h>
#include <asm/arch/mem.h>
#include <asm/cache.h>
+#include <asm/armv7.h>
+#include <asm/arch/gpio.h>
+#include <asm/omap_common.h>
+#include <i2c.h>
+/* Declarations */
extern omap3_sysinfo sysinfo;
+static void omap3_setup_aux_cr(void);
+static void omap3_invalidate_l2_cache_secure(void);
-/******************************************************************************
- * Routine: delay
- * Description: spinning delay to use before udelay works
- *****************************************************************************/
-static inline void delay(unsigned long loops)
+static const struct gpio_bank gpio_bank_34xx[6] = {
+ { (void *)OMAP34XX_GPIO1_BASE, METHOD_GPIO_24XX },
+ { (void *)OMAP34XX_GPIO2_BASE, METHOD_GPIO_24XX },
+ { (void *)OMAP34XX_GPIO3_BASE, METHOD_GPIO_24XX },
+ { (void *)OMAP34XX_GPIO4_BASE, METHOD_GPIO_24XX },
+ { (void *)OMAP34XX_GPIO5_BASE, METHOD_GPIO_24XX },
+ { (void *)OMAP34XX_GPIO6_BASE, METHOD_GPIO_24XX },
+};
+
+const struct gpio_bank *const omap_gpio_bank = gpio_bank_34xx;
+
+#ifdef CONFIG_SPL_BUILD
+/*
+* We use static variables because global data is not ready yet.
+* Initialized data is available in SPL right from the beginning.
+* We would not typically need to save these parameters in regular
+* U-Boot. This is needed only in SPL at the moment.
+*/
+u32 omap3_boot_device = BOOT_DEVICE_NAND;
+
+/* auto boot mode detection is not possible for OMAP3 - hard code */
+u32 omap_boot_mode(void)
+{
+ switch (omap_boot_device()) {
+ case BOOT_DEVICE_MMC2:
+ return MMCSD_MODE_RAW;
+ case BOOT_DEVICE_MMC1:
+ return MMCSD_MODE_FAT;
+ break;
+ case BOOT_DEVICE_NAND:
+ return NAND_MODE_HW_ECC;
+ break;
+ default:
+ puts("spl: ERROR: unknown device - can't select boot mode\n");
+ hang();
+ }
+}
+
+u32 omap_boot_device(void)
{
- __asm__ volatile ("1:\n" "subs %0, %1, #1\n"
- "bne 1b":"=r" (loops):"0"(loops));
+ return omap3_boot_device;
}
+void spl_board_init(void)
+{
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+}
+#endif /* CONFIG_SPL_BUILD */
+
+
/******************************************************************************
* Routine: secure_unlock
* Description: Setup security registers for access
{
unsigned long i;
- /* configrue non-secure access control register */
+ /* configure non-secure access control register */
__asm__ __volatile__("mrc p15, 0, %0, c1, c1, 2":"=r"(i));
/* enabling co-processor CP10 and CP11 accesses in NS world */
__asm__ __volatile__("orr %0, %0, #0xC00":"=r"(i));
try_unlock_memory();
- /*
- * Right now flushing at low MPU speed.
- * Need to move after clock init
- */
- invalidate_dcache(get_device_type());
-#ifndef CONFIG_ICACHE_OFF
- icache_enable();
-#endif
+ /* Errata workarounds */
+ omap3_setup_aux_cr();
-#ifdef CONFIG_L2_OFF
- l2_cache_disable();
-#else
- l2_cache_enable();
+#ifndef CONFIG_SYS_L2CACHE_OFF
+ /* Invalidate L2-cache from secure mode */
+ omap3_invalidate_l2_cache_secure();
#endif
- /*
- * Writing to AuxCR in U-boot using SMI for GP DEV
- * Currently SMI in Kernel on ES2 devices seems to have an issue
- * Once that is resolved, we can postpone this config to kernel
- */
- if (get_device_type() == GP_DEVICE)
- setup_auxcr();
set_muxconf_regs();
- delay(100);
+ sdelay(100);
prcm_init();
per_clocks_enable();
+#ifdef CONFIG_USB_EHCI_OMAP
+ ehci_clocks_enable();
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+ preloader_console_init();
+
+ timer_init();
+#endif
+
if (!in_sdram)
mem_init();
}
{
}
-#ifdef CONFIG_NAND_OMAP_GPMC
+#if defined(CONFIG_NAND_OMAP_GPMC) & !defined(CONFIG_SPL_BUILD)
/******************************************************************************
* OMAP3 specific command to switch between NAND HW and SW ecc
*****************************************************************************/
"[hw/sw] - Switch between NAND hardware (hw) or software (sw) ecc algorithm"
);
-#endif /* CONFIG_NAND_OMAP_GPMC */
+#endif /* CONFIG_NAND_OMAP_GPMC & !CONFIG_SPL_BUILD */
#ifdef CONFIG_DISPLAY_BOARDINFO
/**
return 0;
}
#endif /* CONFIG_DISPLAY_BOARDINFO */
+
+static void omap3_emu_romcode_call(u32 service_id, u32 *parameters)
+{
+ u32 i, num_params = *parameters;
+ u32 *sram_scratch_space = (u32 *)OMAP3_PUBLIC_SRAM_SCRATCH_AREA;
+
+ /*
+ * copy the parameters to an un-cached area to avoid coherency
+ * issues
+ */
+ for (i = 0; i < num_params; i++) {
+ __raw_writel(*parameters, sram_scratch_space);
+ parameters++;
+ sram_scratch_space++;
+ }
+
+ /* Now make the PPA call */
+ do_omap3_emu_romcode_call(service_id, OMAP3_PUBLIC_SRAM_SCRATCH_AREA);
+}
+
+static void omap3_update_aux_cr_secure(u32 set_bits, u32 clear_bits)
+{
+ u32 acr;
+
+ /* Read ACR */
+ asm volatile ("mrc p15, 0, %0, c1, c0, 1" : "=r" (acr));
+ acr &= ~clear_bits;
+ acr |= set_bits;
+
+ if (get_device_type() == GP_DEVICE) {
+ omap3_gp_romcode_call(OMAP3_GP_ROMCODE_API_WRITE_ACR,
+ acr);
+ } else {
+ struct emu_hal_params emu_romcode_params;
+ emu_romcode_params.num_params = 1;
+ emu_romcode_params.param1 = acr;
+ omap3_emu_romcode_call(OMAP3_EMU_HAL_API_WRITE_ACR,
+ (u32 *)&emu_romcode_params);
+ }
+}
+
+static void omap3_update_aux_cr(u32 set_bits, u32 clear_bits)
+{
+ u32 acr;
+
+ /* Read ACR */
+ asm volatile ("mrc p15, 0, %0, c1, c0, 1" : "=r" (acr));
+ acr &= ~clear_bits;
+ acr |= set_bits;
+
+ /* Write ACR - affects non-secure banked bits */
+ asm volatile ("mcr p15, 0, %0, c1, c0, 1" : : "r" (acr));
+}
+
+static void omap3_setup_aux_cr(void)
+{
+ /* Workaround for Cortex-A8 errata: #454179 #430973
+ * Set "IBE" bit
+ * Set "Disable Branch Size Mispredicts" bit
+ * Workaround for erratum #621766
+ * Enable L1NEON bit
+ * ACR |= (IBE | DBSM | L1NEON) => ACR |= 0xE0
+ */
+ omap3_update_aux_cr_secure(0xE0, 0);
+}
+
+#ifndef CONFIG_SYS_L2CACHE_OFF
+/* Invalidate the entire L2 cache from secure mode */
+static void omap3_invalidate_l2_cache_secure(void)
+{
+ if (get_device_type() == GP_DEVICE) {
+ omap3_gp_romcode_call(OMAP3_GP_ROMCODE_API_L2_INVAL,
+ 0);
+ } else {
+ struct emu_hal_params emu_romcode_params;
+ emu_romcode_params.num_params = 1;
+ emu_romcode_params.param1 = 0;
+ omap3_emu_romcode_call(OMAP3_EMU_HAL_API_L2_INVAL,
+ (u32 *)&emu_romcode_params);
+ }
+}
+
+void v7_outer_cache_enable(void)
+{
+ /* Set L2EN */
+ omap3_update_aux_cr_secure(0x2, 0);
+
+ /*
+ * On some revisions L2EN bit is banked on some revisions it's not
+ * No harm in setting both banked bits(in fact this is required
+ * by an erratum)
+ */
+ omap3_update_aux_cr(0x2, 0);
+}
+
+void v7_outer_cache_disable(void)
+{
+ /* Clear L2EN */
+ omap3_update_aux_cr_secure(0, 0x2);
+
+ /*
+ * On some revisions L2EN bit is banked on some revisions it's not
+ * No harm in clearing both banked bits(in fact this is required
+ * by an erratum)
+ */
+ omap3_update_aux_cr(0, 0x2);
+}
+#endif
+
+#ifndef CONFIG_SYS_DCACHE_OFF
+void enable_caches(void)
+{
+ /* Enable D-cache. I-cache is already enabled in start.S */
+ dcache_enable();
+}
+#endif