*/
#include <common.h>
+#include <dm.h>
#include <errno.h>
+#include <ns16550.h>
#include <spl.h>
#include <asm/arch/cpu.h>
#include <asm/arch/hardware.h>
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_DM_GPIO
+static const struct omap_gpio_platdata am33xx_gpio[] = {
+ { 0, AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
+ { 1, AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
+ { 2, AM33XX_GPIO2_BASE, METHOD_GPIO_24XX },
+ { 3, AM33XX_GPIO3_BASE, METHOD_GPIO_24XX },
+#ifdef CONFIG_AM43XX
+ { 4, AM33XX_GPIO4_BASE, METHOD_GPIO_24XX },
+ { 5, AM33XX_GPIO5_BASE, METHOD_GPIO_24XX },
+#endif
+};
+
+U_BOOT_DEVICES(am33xx_gpios) = {
+ { "gpio_omap", &am33xx_gpio[0] },
+ { "gpio_omap", &am33xx_gpio[1] },
+ { "gpio_omap", &am33xx_gpio[2] },
+ { "gpio_omap", &am33xx_gpio[3] },
+#ifdef CONFIG_AM43XX
+ { "gpio_omap", &am33xx_gpio[4] },
+ { "gpio_omap", &am33xx_gpio[5] },
+#endif
+};
+
+# ifndef CONFIG_OF_CONTROL
+/*
+ * TODO(sjg@chromium.org): When we can move SPL serial to DM, we can remove
+ * the CONFIGs. At the same time, we should move this to the board files.
+ */
+static const struct ns16550_platdata am33xx_serial[] = {
+ { CONFIG_SYS_NS16550_COM1, 2, CONFIG_SYS_NS16550_CLK },
+# ifdef CONFIG_SYS_NS16550_COM2
+ { CONFIG_SYS_NS16550_COM2, 2, CONFIG_SYS_NS16550_CLK },
+# ifdef CONFIG_SYS_NS16550_COM3
+ { CONFIG_SYS_NS16550_COM3, 2, CONFIG_SYS_NS16550_CLK },
+ { CONFIG_SYS_NS16550_COM4, 2, CONFIG_SYS_NS16550_CLK },
+ { CONFIG_SYS_NS16550_COM5, 2, CONFIG_SYS_NS16550_CLK },
+ { CONFIG_SYS_NS16550_COM6, 2, CONFIG_SYS_NS16550_CLK },
+# endif
+# endif
+};
+
+U_BOOT_DEVICES(am33xx_uarts) = {
+ { "serial_omap", &am33xx_serial[0] },
+# ifdef CONFIG_SYS_NS16550_COM2
+ { "serial_omap", &am33xx_serial[1] },
+# ifdef CONFIG_SYS_NS16550_COM3
+ { "serial_omap", &am33xx_serial[2] },
+ { "serial_omap", &am33xx_serial[3] },
+ { "serial_omap", &am33xx_serial[4] },
+ { "serial_omap", &am33xx_serial[5] },
+# endif
+# endif
+};
+# endif
+
+#else
+
static const struct gpio_bank gpio_bank_am33xx[] = {
{ (void *)AM33XX_GPIO0_BASE, METHOD_GPIO_24XX },
{ (void *)AM33XX_GPIO1_BASE, METHOD_GPIO_24XX },
const struct gpio_bank *const omap_gpio_bank = gpio_bank_am33xx;
+#endif
+
#if defined(CONFIG_OMAP_HSMMC) && !defined(CONFIG_SPL_BUILD)
int cpu_mmc_init(bd_t *bis)
{
;
}
+#ifdef CONFIG_SPL_BUILD
+void board_init_f(ulong dummy)
+{
+ board_early_init_f();
+ sdram_init();
+}
+#endif
+
void s_init(void)
{
/*
*/
#ifdef CONFIG_NOR_BOOT
enable_norboot_pin_mux();
-#endif
- /*
- * Save the boot parameters passed from romcode.
- * We cannot delay the saving further than this,
- * to prevent overwrites.
- */
-#ifdef CONFIG_SPL_BUILD
- save_omap_boot_params();
#endif
watchdog_disable();
- timer_init();
set_uart_mux_conf();
setup_clocks_for_console();
uart_soft_reset();
#if defined(CONFIG_NOR_BOOT) || defined(CONFIG_QSPI_BOOT)
+ /* TODO: This does not work, gd is not available yet */
gd->baudrate = CONFIG_BAUDRATE;
serial_init();
gd->have_console = 1;
-#elif defined(CONFIG_SPL_BUILD)
- gd = &gdata;
- preloader_console_init();
#endif
#if defined(CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC)
/* Enable RTC32K clock */
rtc32k_enable();
#endif
-#ifdef CONFIG_SPL_BUILD
- board_early_init_f();
- sdram_init();
-#endif
}
#endif
-
-#ifndef CONFIG_SYS_DCACHE_OFF
-void enable_caches(void)
-{
- /* Enable D-cache. I-cache is already enabled in start.S */
- dcache_enable();
-}
-#endif /* !CONFIG_SYS_DCACHE_OFF */