#include <asm/errno.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
+#include <asm/arch/dma.h>
#include <asm/arch/gpio.h>
#include <asm/arch/iomux.h>
#include <asm/arch/imx-regs.h>
void reset_cpu(ulong ignored)
{
-
struct mx28_rtc_regs *rtc_regs =
(struct mx28_rtc_regs *)MXS_RTC_BASE;
+ struct mx28_lcdif_regs *lcdif_regs =
+ (struct mx28_lcdif_regs *)MXS_LCDIF_BASE;
+
+ /*
+ * Shut down the LCD controller as it interferes with BootROM boot mode
+ * pads sampling.
+ */
+ writel(LCDIF_CTRL_RUN, &lcdif_regs->hw_lcdif_ctrl_clr);
/* Wait 1 uS before doing the actual watchdog reset */
writel(1, &rtc_regs->hw_rtc_watchdog);
;
}
-int mx28_wait_mask_set(struct mx28_register *reg, uint32_t mask, int timeout)
+void enable_caches(void)
+{
+#ifndef CONFIG_SYS_ICACHE_OFF
+ icache_enable();
+#endif
+#ifndef CONFIG_SYS_DCACHE_OFF
+ dcache_enable();
+#endif
+}
+
+int mx28_wait_mask_set(struct mx28_register_32 *reg, uint32_t mask, int timeout)
{
while (--timeout) {
if ((readl(®->reg) & mask) == mask)
return !timeout;
}
-int mx28_wait_mask_clr(struct mx28_register *reg, uint32_t mask, int timeout)
+int mx28_wait_mask_clr(struct mx28_register_32 *reg, uint32_t mask, int timeout)
{
while (--timeout) {
if ((readl(®->reg) & mask) == 0)
return !timeout;
}
-int mx28_reset_block(struct mx28_register *reg)
+int mx28_reset_block(struct mx28_register_32 *reg)
{
/* Clear SFTRST */
writel(MX28_BLOCK_SFTRST, ®->reg_clr);
}
#endif
-#ifdef CONFIG_ARCH_CPU_INIT
int arch_cpu_init(void)
{
struct mx28_clkctrl_regs *clkctrl_regs =
*/
mxs_gpio_init();
+#ifdef CONFIG_APBH_DMA
+ /* Start APBH DMA */
+ mxs_dma_init();
+#endif
+
return 0;
}
-#endif
#if defined(CONFIG_DISPLAY_CPUINFO)
int print_cpuinfo(void)
{
+ struct mx28_spl_data *data = (struct mx28_spl_data *)
+ ((CONFIG_SYS_TEXT_BASE - sizeof(struct mx28_spl_data)) & ~0xf);
+
printf("Freescale i.MX28 family at %d MHz\n",
mxc_get_clock(MXC_ARM_CLK) / 1000000);
+ printf("BOOT: %s\n", mx28_boot_modes[data->boot_mode_idx].mode);
return 0;
}
#endif
int mx28_dram_init(void)
{
- struct mx28_digctl_regs *digctl_regs =
- (struct mx28_digctl_regs *)MXS_DIGCTL_BASE;
- uint32_t sz[2];
-
- sz[0] = readl(&digctl_regs->hw_digctl_scratch0);
- sz[1] = readl(&digctl_regs->hw_digctl_scratch1);
+ struct mx28_spl_data *data = (struct mx28_spl_data *)
+ ((CONFIG_SYS_TEXT_BASE - sizeof(struct mx28_spl_data)) & ~0xf);
- if (sz[0] != sz[1]) {
+ if (data->mem_dram_size == 0) {
printf("MX28:\n"
- "Error, the RAM size in HW_DIGCTRL_SCRATCH0 and\n"
- "HW_DIGCTRL_SCRATCH1 is not the same. Please\n"
- "verify these two registers contain valid RAM size!\n");
+ "Error, the RAM size passed up from SPL is 0!\n");
hang();
}
- gd->ram_size = sz[0];
+ gd->ram_size = data->mem_dram_size;
return 0;
}