/*
* (C) Copyright 2007-2008
- * Stelian Pop <stelian.pop@leadtechdesign.com>
+ * Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* (C) Copyright 2009-2011
#include <common.h>
#include <asm/io.h>
-#include <asm/arch/hardware.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
-#include <asm/arch/at91_pio.h>
+#include <asm/arch/gpio.h>
+
+/*
+ * if CONFIG_AT91_GPIO_PULLUP ist set, keep pullups on on all
+ * peripheral pins. Good to have if hardware is soldered optionally
+ * or in case of SPI no slave is selected. Avoid lines to float
+ * needlessly. Use a short local PUP define.
+ *
+ * Due to errata "TXD floats when CTS is inactive" pullups are always
+ * on for TXD pins.
+ */
+#ifdef CONFIG_AT91_GPIO_PULLUP
+# define PUP CONFIG_AT91_GPIO_PULLUP
+#else
+# define PUP 0
+#endif
void at91_serial0_hw_init(void)
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_a_periph(AT91_PIO_PORTA, 26, 1); /* TXD0 */
- at91_set_a_periph(AT91_PIO_PORTA, 27, 0); /* RXD0 */
+ at91_set_a_periph(AT91_PIO_PORTA, 27, PUP); /* RXD0 */
writel(1 << ATMEL_ID_USART0, &pmc->pcer);
}
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_a_periph(AT91_PIO_PORTD, 0, 1); /* TXD1 */
- at91_set_a_periph(AT91_PIO_PORTD, 1, 0); /* RXD1 */
+ at91_set_a_periph(AT91_PIO_PORTD, 1, PUP); /* RXD1 */
writel(1 << ATMEL_ID_USART1, &pmc->pcer);
}
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
at91_set_a_periph(AT91_PIO_PORTD, 2, 1); /* TXD2 */
- at91_set_a_periph(AT91_PIO_PORTD, 3, 0); /* RXD2 */
+ at91_set_a_periph(AT91_PIO_PORTD, 3, PUP); /* RXD2 */
writel(1 << ATMEL_ID_USART2, &pmc->pcer);
}
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
- at91_set_a_periph(AT91_PIO_PORTC, 30, 0); /* DRXD */
+ at91_set_a_periph(AT91_PIO_PORTC, 30, PUP); /* DRXD */
at91_set_a_periph(AT91_PIO_PORTC, 31, 1); /* DTXD */
writel(1 << ATMEL_ID_SYS, &pmc->pcer);
}
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
- at91_set_b_periph(AT91_PIO_PORTA, 0, 0); /* SPI0_MISO */
- at91_set_b_periph(AT91_PIO_PORTA, 1, 0); /* SPI0_MOSI */
- at91_set_b_periph(AT91_PIO_PORTA, 2, 0); /* SPI0_SPCK */
+ at91_set_b_periph(AT91_PIO_PORTA, 0, PUP); /* SPI0_MISO */
+ at91_set_b_periph(AT91_PIO_PORTA, 1, PUP); /* SPI0_MOSI */
+ at91_set_b_periph(AT91_PIO_PORTA, 2, PUP); /* SPI0_SPCK */
/* Enable clock */
writel(1 << ATMEL_ID_SPI0, &pmc->pcer);
{
at91_pmc_t *pmc = (at91_pmc_t *) ATMEL_BASE_PMC;
- at91_set_a_periph(AT91_PIO_PORTB, 12, 0); /* SPI1_MISO */
- at91_set_a_periph(AT91_PIO_PORTB, 13, 0); /* SPI1_MOSI */
- at91_set_a_periph(AT91_PIO_PORTB, 14, 0); /* SPI1_SPCK */
+ at91_set_a_periph(AT91_PIO_PORTB, 12, PUP); /* SPI1_MISO */
+ at91_set_a_periph(AT91_PIO_PORTB, 13, PUP); /* SPI1_MOSI */
+ at91_set_a_periph(AT91_PIO_PORTB, 14, PUP); /* SPI1_SPCK */
/* Enable clock */
writel(1 << ATMEL_ID_SPI1, &pmc->pcer);