information that is embedded into the binary to support U-Boot
relocating itself to the top-of-RAM later during execution.
-config SYS_INIT_SP_BSS_OFFSET
- int
+config INIT_SP_RELATIVE
+ bool "Specify the early stack pointer relative to the .bss section"
help
U-Boot typically uses a hard-coded value for the stack pointer
- before relocation. Define this option to instead calculate the
+ before relocation. Enable this option to instead calculate the
initial SP at run-time. This is useful to avoid hard-coding addresses
into U-Boot, so that can be loaded and executed at arbitrary
- addresses and thus avoid using arbitrary addresses at runtime. This
- option's value is the offset added to &_bss_start in order to
+ addresses and thus avoid using arbitrary addresses at runtime.
+
+ If this option is enabled, the early stack pointer is set to
+ &_bss_start with a offset value added. The offset is specified by
+ SYS_INIT_SP_BSS_OFFSET.
+
+config SYS_INIT_SP_BSS_OFFSET
+ int "Early stack offset from the .bss base address"
+ depends on INIT_SP_RELATIVE
+ default 524288
+ help
+ This option's value is the offset added to &_bss_start in order to
calculate the stack pointer. This offset should be large enough so
that the early malloc region, global data (gd), and early stack usage
do not overlap any appended DTB.
config ARCH_QEMU
bool "QEMU Virtual Platform"
+ select ARCH_SUPPORT_TFABOOT
select DM
select DM_SERIAL
select OF_CONTROL
select SPL_STACK_R if SPL
select SPL_SYS_MALLOC_SIMPLE if SPL
select SPL_SYS_THUMB_BUILD if !ARM64
+ select SUNXI_GPIO
select SYS_NS16550
select SYS_THUMB_BUILD if !ARM64
select USB if DISTRO_DEFAULTS
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
select SUPPORT_SPL
select FSL_DDR_INTERACTIVE if !SD_BOOT
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
select SUPPORT_SPL
imply SCSI
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
select SUPPORT_SPL
select FSL_DDR_BIST
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
help
Support for NXP LX2160ARDB platform.
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
help
Support for NXP LX2160AQDS platform.
bool "Support ls1012aqds"
select ARCH_LS1012A
select ARM64
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
help
Support for Freescale LS1012AQDS platform.
bool "Support ls1012ardb"
select ARCH_LS1012A
select ARM64
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
imply SCSI
imply SCSI_AHCI
bool "Support ls1012a2g5rdb"
select ARCH_LS1012A
select ARM64
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
imply SCSI
help
bool "Support ls1012afrwy"
select ARCH_LS1012A
select ARM64
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
imply SCSI
imply SCSI_AHCI
bool "Support ls1012afrdm"
select ARCH_LS1012A
select ARM64
+ select ARCH_SUPPORT_TFABOOT
help
Support for Freescale LS1012AFRDM platform.
The LS1012A Freedom board (FRDM) is a high-performance
development platform that supports the QorIQ LS1012A
Layerscape Architecture processor.
+config TARGET_LS1028AQDS
+ bool "Support ls1028aqds"
+ select ARCH_LS1028A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
+ help
+ Support for Freescale LS1028AQDS platform
+ The LS1028A Development System (QDS) is a high-performance
+ development platform that supports the QorIQ LS1028A
+ Layerscape Architecture processor.
+
+config TARGET_LS1028ARDB
+ bool "Support ls1028ardb"
+ select ARCH_LS1028A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
+ help
+ Support for Freescale LS1028ARDB platform
+ The LS1028A Development System (RDB) is a high-performance
+ development platform that supports the QorIQ LS1028A
+ Layerscape Architecture processor.
+
config TARGET_LS1088ARDB
bool "Support ls1088ardb"
select ARCH_LS1088A
select ARCH_MISC_INIT
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_LATE_INIT
select SUPPORT_SPL
select FSL_DDR_INTERACTIVE if !SD_BOOT
select ARCH_LS1043A
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select SUPPORT_SPL
select ARCH_LS1043A
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select SUPPORT_SPL
select ARCH_LS1046A
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select DM_SPI_FLASH if DM_SPI
select ARCH_LS1046A
select ARM64
select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
select BOARD_EARLY_INIT_F
select BOARD_LATE_INIT
select DM_SPI_FLASH if DM_SPI
development platform that supports the QorIQ LS1046A
Layerscape Architecture processor.
+config TARGET_LS1046AFRWY
+ bool "Support ls1046afrwy"
+ select ARCH_LS1046A
+ select ARM64
+ select ARMV8_MULTIENTRY
+ select ARCH_SUPPORT_TFABOOT
+ select BOARD_EARLY_INIT_F
+ select BOARD_LATE_INIT
+ select DM_SPI_FLASH if DM_SPI
+ imply SCSI
+ help
+ Support for Freescale LS1046AFRWY platform.
+ The LS1046A Freeway Board (FRWY) is a high-performance
+ development platform that supports the QorIQ LS1046A
+ Layerscape Architecture processor.
config TARGET_H2200
bool "Support h2200"
select CPU_PXA
-config TARGET_ZIPITZ2
- bool "Support zipitz2"
- select CPU_PXA
-
config TARGET_COLIBRI_PXA270
bool "Support colibri_pxa270"
select CPU_PXA
select MISC
select OF_CONTROL
select OF_LIBFDT
+ select OF_SYSTEM_SETUP
select PINCTRL
select REGMAP
select SUPPORT_SPL
imply CMD_DM
imply CMD_POWEROFF
imply ENV_VARS_UBOOT_RUNTIME_CONFIG
+ imply USE_PREBOOT
help
Support for STM32MP SoC family developed by STMicroelectronics,
MPUs based on ARM cortex A core
endchoice
+config ARCH_SUPPORT_TFABOOT
+ bool
+
+config TFABOOT
+ bool "Support for booting from TF-A"
+ depends on ARCH_SUPPORT_TFABOOT
+ default n
+ help
+ Enabling this will make a U-Boot binary that is capable of being
+ booted via TF-A.
+
config TI_SECURE_DEVICE
bool "HS Device Type Support"
depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS || ARCH_K3
source "board/freescale/ls2080aqds/Kconfig"
source "board/freescale/ls2080ardb/Kconfig"
source "board/freescale/ls1088a/Kconfig"
+source "board/freescale/ls1028a/Kconfig"
source "board/freescale/ls1021aqds/Kconfig"
source "board/freescale/ls1043aqds/Kconfig"
source "board/freescale/ls1021atwr/Kconfig"
source "board/freescale/ls1046aqds/Kconfig"
source "board/freescale/ls1043ardb/Kconfig"
source "board/freescale/ls1046ardb/Kconfig"
+source "board/freescale/ls1046afrwy/Kconfig"
source "board/freescale/ls1012aqds/Kconfig"
source "board/freescale/ls1012ardb/Kconfig"
source "board/freescale/ls1012afrdm/Kconfig"
source "board/xilinx/Kconfig"
source "board/xilinx/zynq/Kconfig"
source "board/xilinx/zynqmp/Kconfig"
-source "board/zipitz2/Kconfig"
source "arch/arm/Kconfig.debug"