+# SPDX-License-Identifier: GPL-2.0+
#
# (C) Copyright 2000 - 2013
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
Summary:
========
- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
-- Marvell Family Member
- CONFIG_SYS_MVFS - define it if you want to enable
- multiple fs option at one time
- for marvell soc family
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
pointer. This is needed for the temporary stack before
relocation.
- CONFIG_SYS_MIPS_CACHE_MODE
-
- Cache operation mode for the MIPS CPU.
- See also arch/mips/include/asm/mipsregs.h.
- Possible values are:
- CONF_CM_CACHABLE_NO_WA
- CONF_CM_CACHABLE_WA
- CONF_CM_UNCACHED
- CONF_CM_CACHABLE_NONCOHERENT
- CONF_CM_CACHABLE_CE
- CONF_CM_CACHABLE_COW
- CONF_CM_CACHABLE_CUW
- CONF_CM_CACHABLE_ACCELERATED
-
- CONFIG_SYS_XWAY_EBU_BOOTCFG
-
- Special option for Lantiq XWAY SoCs for booting from NOR flash.
- See also arch/mips/cpu/mips32/start.S.
-
CONFIG_XWAY_SWAP_BYTES
Enable compilation of tools/xway-swap-bytes needed for Lantiq
CONFIG_AT91_HW_WDT_TIMEOUT
specify the timeout in seconds. default 2 seconds.
-- U-Boot Version:
- CONFIG_VERSION_VARIABLE
- If this variable is defined, an environment variable
- named "ver" is created by U-Boot showing the U-Boot
- version as printed by the "version" command.
- Any change to this variable will be reverted at the
- next reset.
-
- Real-Time Clock:
When CONFIG_CMD_DATE is selected, the type of the RTC
CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
bootloader. Note 2TB partition limit; see
disk/part_efi.c
- CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
-
- If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
- CONFIG_DRIVER_TI_EMAC
- Support for davinci emac
-
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
Define this if you have more then 3 PHYs.
CONFIG_SUPPORT_EMMC_BOOT
Enable some additional features of the eMMC boot partitions.
- CONFIG_SUPPORT_EMMC_RPMB
- Enable the commands for reading, writing and programming the
- key for the Replay Protection Memory Block partition in eMMC.
-
- USB Device Firmware Update (DFU) class support:
CONFIG_DFU_OVER_USB
This enables the USB portion of the DFU USB class
be at least 4MB.
- MII/PHY support:
- CONFIG_PHY_ADDR
-
- The address of PHY on MII bus.
-
CONFIG_PHY_CLOCK_FREQ (ppc4xx)
The clock frequency of the MII bus
the environment like the "source" command or the
boot command first.
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
- Define this in order to add variables describing certain
- run-time determined information about the hardware to the
- environment. These will be named board_name, board_rev.
-
CONFIG_DELAY_ENVIRONMENT
Normally the environment is loaded when the board is
A better solution is to properly configure the firewall,
but sometimes that is not allowed.
-- bootcount support:
- CONFIG_AT91SAM9XE
- enable special bootcounter support on at91sam9xe based boards.
-
- Show boot progress:
CONFIG_SHOW_BOOT_PROGRESS
-150 common/cmd_nand.c Incorrect FIT image format
151 common/cmd_nand.c FIT image format OK
-- legacy image format:
- CONFIG_IMAGE_FORMAT_LEGACY
- enables the legacy image format support in U-Boot.
-
- Default:
- enabled if CONFIG_FIT_SIGNATURE is not defined.
-
- CONFIG_DISABLE_IMAGE_LEGACY
- disable the legacy image format
-
- This define is introduced, as the legacy image format is
- enabled per default for backward compatibility.
-
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
for a more detailed description refer to doc/README.update.
- MTD Support (mtdparts command, UBI support)
- CONFIG_MTD_DEVICE
-
- Adds the MTD device infrastructure from the Linux kernel.
- Needed for mtdparts command support.
-
- CONFIG_MTD_PARTITIONS
-
- Adds the MTD partitioning infrastructure from the Linux
- kernel. Needed for UBI support.
-
-- UBI support
- CONFIG_UBI_SILENCE_MSG
-
- Make the verbose messages from UBI stop printing. This leaves
- warnings and errors enabled.
-
-
CONFIG_MTD_UBI_WL_THRESHOLD
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
Enable UBI fastmap debug
default: 0
-- UBIFS support
- CONFIG_UBIFS_SILENCE_MSG
-
- Make the verbose messages from UBIFS stop printing. This leaves
- warnings and errors enabled.
-
- SPL framework
CONFIG_SPL
Enable building of SPL globally.
CONFIG_SPL_NAND_DRIVERS
SPL uses normal NAND drivers, not minimal drivers.
+ CONFIG_SPL_NAND_IDENT
+ SPL uses the chip ID list to identify the NAND flash.
+ Requires CONFIG_SPL_NAND_BASE.
+
CONFIG_SPL_NAND_ECC
Include standard software ECC in the SPL
use an arch-specific makefile fragment instead, for
example if more than one image needs to be produced.
- CONFIG_FIT_SPL_PRINT
+ CONFIG_SPL_FIT_PRINT
Printing information about a FIT image adds quite a bit of
code to SPL. So this is normally disabled in SPL. Use this
option to re-enable it. This will affect the output of the
Begin and End addresses of the area used by the
simple memory test.
-- CONFIG_SYS_ALT_MEMTEST:
- Enable an alternate, more extensive memory test.
-
- CONFIG_SYS_MEMTEST_SCRATCH:
Scratch address used by the alternate memory test
You only need to set this if address zero isn't writeable
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_USE_STDINT
- If stdint.h is available with your toolchain you can define this
- option to enable it. You can provide option 'USE_STDINT=1' when
- building U-Boot to enable this.
-
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:
If defined, the x86 reset vector code is included. This is not
needed when U-Boot is running from Coreboot.
-- CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
- Enables the RTC32K OSC on AM33xx based plattforms
-
- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Option to disable subpage write in NAND driver
driver that uses this:
regular expression. This allows multiple variables to be connected to
the same callback without explicitly listing them all out.
+The signature of the callback functions is:
+
+ int callback(const char *name, const char *value, enum env_op op, int flags)
+
+* name - changed environment variable
+* value - new value of the environment variable
+* op - operation (create, overwrite, or delete)
+* flags - attributes of the environment variable change, see flags H_* in
+ include/search.h
+
+The return value is 0 if the variable change is accepted and 1 otherwise.
Command Line Parsing:
=====================
projects / oweals / u-boot.git / blobdiff