board: amlogic: add support for Odroid-N2

[oweals/u-boot.git] / README

diff --git a/README b/README
index a514f48caefc68b8453b8cc7ce0da3581f3504a8..d2f466e6f6fae82b996db8cc8a329932fe23c666 100644 (file)
--- a/README
+++ b/README
@@ -212,7 +212,7 @@ board. This allows feature development which is not board- or architecture-
 specific to be undertaken on a native platform. The sandbox is also used to
 run some of U-Boot's tests.
 
-See board/sandbox/README.sandbox for more details.
+See doc/arch/index.rst for more details.
 
 
 Board Initialisation Flow:
@@ -486,10 +486,6 @@ The following options need to be configured:
                PBI commands can be used to configure SoC before it starts the execution.
                Please refer doc/README.pblimage for more details
 
-               CONFIG_SPL_FSL_PBL
-               It adds a target to create boot binary having SPL binary in PBI format
-               concatenated with u-boot binary.
-
                CONFIG_SYS_FSL_DDR_BE
                Defines the DDR controller register space as Big Endian
 
@@ -634,8 +630,6 @@ The following options need to be configured:
                the defaults discussed just above.
 
 - Cache Configuration:
-               CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
-               CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
                CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
 
 - Cache Configuration for ARM:
@@ -966,10 +960,6 @@ The following options need to be configured:
                        CONFIG_SH_ETHER_CACHE_WRITEBACK
                        If this option is set, the driver enables cache flush.
 
-- PWM Support:
-               CONFIG_PWM_IMX
-               Support for PWM module on the imx6.
-
 - TPM Support:
                CONFIG_TPM
                Support TPM devices.
@@ -1120,9 +1110,6 @@ The following options need to be configured:
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 
-               CONFIG_SUPPORT_EMMC_BOOT
-               Enable some additional features of the eMMC boot partitions.
-
 - USB Device Firmware Update (DFU) class support:
                CONFIG_DFU_OVER_USB
                This enables the USB portion of the DFU USB class
@@ -2423,9 +2410,6 @@ FIT uImage format:
                When defined, the linker checks that the actual size does
                not exceed it.
 
-               CONFIG_SPL_TEXT_BASE
-               TEXT_BASE for linking the SPL binary.
-
                CONFIG_SPL_RELOC_TEXT_BASE
                Address to relocate to.  If unspecified, this is equal to
                CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
@@ -2554,9 +2538,6 @@ FIT uImage format:
                Defines the size and behavior of the NAND that SPL uses
                to read U-Boot
 
-               CONFIG_SPL_NAND_BOOT
-               Add support NAND boot
-
                CONFIG_SYS_NAND_U_BOOT_OFFS
                Location in NAND to read U-Boot from
 
@@ -3302,12 +3283,12 @@ within that device.
 
 - CONFIG_SYS_FMAN_FW_ADDR
        The address in the storage device where the FMAN microcode is located.  The
-       meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+       meaning of this address depends on which CONFIG_SYS_QE_FMAN_FW_IN_xxx macro
        is also specified.
 
 - CONFIG_SYS_QE_FW_ADDR
        The address in the storage device where the QE microcode is located.  The
-       meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+       meaning of this address depends on which CONFIG_SYS_QE_FMAN_FW_IN_xxx macro
        is also specified.
 
 - CONFIG_SYS_QE_FMAN_FW_LENGTH