multiple fs option at one time
for marvell soc family
-- 8xx CPU Options: (if using an MPC8xx CPU)
- CONFIG_8xx_GCLK_FREQ - CPU clock
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
Define this variable to enable hw flow control in serial driver.
Current user of this option is drivers/serial/nsl16550.c driver
-- Console Interface:
- Depending on board, define exactly one serial port
- (CONFIG_8xx_CONS_SMC1 or CONFIG_8xx_CONS_SMC2),
- or switch off the serial console by defining
- CONFIG_8xx_CONS_NONE
-
- Note: if CONFIG_8xx_CONS_NONE is defined, the serial
- port routines must be defined elsewhere
- (i.e. serial_init(), serial_getc(), ...)
-
- Console Baudrate:
CONFIG_BAUDRATE - in bps
Select one of the baudrates listed in
CONFIG_SYS_BAUDRATE_TABLE, see below.
- CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
-
-- Console Rx buffer length
- With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
- the maximum receive buffer length for the SMC.
- This option is actual only for 8xx possible.
- If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
- must be defined, to setup the maximum idle timeout for
- the SMC.
- Autoboot Command:
CONFIG_BOOTCOMMAND
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SANDBOX * sb command to access sandbox features
CONFIG_CMD_SAVES * save S record dump
- CONFIG_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SF * Read/write/erase SPI NOR flash
Default is 32bit.
- SCSI Support:
- At the moment only there is only support for the
- SYM53C8XX SCSI controller; define
- CONFIG_SCSI_SYM53C8XX to enable it.
-
CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
maximum numbers of LUNs, SCSI ID's and target
devices.
- CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
The environment variable 'scsidevs' is set to the number of
SCSI devices found during the last scan.
point to an otherwise UNUSED address space between
the top of RAM and the start of the PCI space.
-- CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
-
-- CONFIG_SYS_SYPCR: System Protection Control (11-9)
-
-- CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
-
-- CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
-
-- CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
-
- CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
- CONFIG_SYS_OR_TIMING_SDRAM:
- CONFIG_SYS_MAMR_PTA:
periodic timer for refresh
-- CONFIG_SYS_DER: Debug Event Register (37-47)
-
- FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
Only for 83xx systems. If specified, then DDR should
be configured using CS0 and CS1 instead of CS2 and CS3.
-- CONFIG_ETHER_ON_FEC[12]
- Define to enable FEC[12] on a 8xx series processor.
-
-- CONFIG_FEC[12]_PHY
- Define to the hardcoded PHY address which corresponds
- to the given FEC; i. e.
- #define CONFIG_FEC1_PHY 4
- means that the PHY with address 4 is connected to FEC1
-
- When set to -1, means to probe for first available.
-
-- CONFIG_FEC[12]_PHY_NORXERR
- The PHY does not have a RXERR line (RMII only).
- (so program the FEC to ignore it).
-
- CONFIG_RMII
Enable RMII mode for all FECs.
Note that this is a global option, we can't