efi_loader: use const efi_guid_t * for variable services

[oweals/u-boot.git] / README

diff --git a/README b/README
index 09822a317da8da4e71f8af460b1d305af4bcd9cd..b81500f6afdd8da522d576933b85e3f7c750c788 100644 (file)
--- a/README
+++ b/README
@@ -528,25 +528,6 @@ The following options need to be configured:
                pointer. This is needed for the temporary stack before
                relocation.
 
-               CONFIG_SYS_MIPS_CACHE_MODE
-
-               Cache operation mode for the MIPS CPU.
-               See also arch/mips/include/asm/mipsregs.h.
-               Possible values are:
-                       CONF_CM_CACHABLE_NO_WA
-                       CONF_CM_CACHABLE_WA
-                       CONF_CM_UNCACHED
-                       CONF_CM_CACHABLE_NONCOHERENT
-                       CONF_CM_CACHABLE_CE
-                       CONF_CM_CACHABLE_COW
-                       CONF_CM_CACHABLE_CUW
-                       CONF_CM_CACHABLE_ACCELERATED
-
-               CONFIG_SYS_XWAY_EBU_BOOTCFG
-
-               Special option for Lantiq XWAY SoCs for booting from NOR flash.
-               See also arch/mips/cpu/mips32/start.S.
-
                CONFIG_XWAY_SWAP_BYTES
 
                Enable compilation of tools/xway-swap-bytes needed for Lantiq
@@ -1165,9 +1146,6 @@ The following options need to be configured:
                CONFIG_DFU_OVER_USB
                This enables the USB portion of the DFU USB class
 
-               CONFIG_DFU_MMC
-               This enables support for exposing (e)MMC devices via DFU.
-
                CONFIG_DFU_NAND
                This enables support for exposing NAND devices via DFU.
 
@@ -1448,15 +1426,6 @@ The following options need to be configured:
                forwarded through a router.
                (Environment variable "netmask")
 
-- Multicast TFTP Mode:
-               CONFIG_MCAST_TFTP
-
-               Defines whether you want to support multicast TFTP as per
-               rfc-2090; for example to work with atftp.  Lets lots of targets
-               tftp down the same boot image concurrently.  Note: the Ethernet
-               driver in use must provide a function: mcast() to join/leave a
-               multicast group.
-
 - BOOTP Recovery Mode:
                CONFIG_BOOTP_RANDOM_DELAY
 
@@ -1951,14 +1920,6 @@ The following options need to be configured:
                SPI configuration items (port pins to use, etc). For
                an example, see include/configs/sacsng.h.
 
-               CONFIG_HARD_SPI
-
-               Enables a hardware SPI driver for general-purpose reads
-               and writes.  As with CONFIG_SOFT_SPI, the board configuration
-               must define a list of chip-select function pointers.
-               Currently supported on some MPC8xxx processors.  For an
-               example, see include/configs/mpc8349emds.h.
-
                CONFIG_SYS_SPI_MXC_WAIT
                Timeout for waiting until spi transfer completed.
                default: (CONFIG_SYS_HZ/100)     /* 10 ms */
@@ -2025,13 +1986,6 @@ The following options need to be configured:
                200 ms.
 
 - Configuration Management:
-               CONFIG_BUILD_TARGET
-
-               Some SoCs need special image types (e.g. U-Boot binary
-               with a special header) as build targets. By defining
-               CONFIG_BUILD_TARGET in the SoC / board header, this
-               special image will be automatically built upon calling
-               make / buildman.
 
                CONFIG_IDENT_STRING
 
@@ -3256,8 +3210,8 @@ Low Level (hardware related) configuration options:
                a 16 bit bus.
                Not all NAND drivers use this symbol.
                Example of drivers that use it:
-               - drivers/mtd/nand/ndfc.c
-               - drivers/mtd/nand/mxc_nand.c
+               - drivers/mtd/nand/raw/ndfc.c
+               - drivers/mtd/nand/raw/mxc_nand.c
 
 - CONFIG_SYS_NDFC_EBC0_CFG
                Sets the EBC0_CFG register for the NDFC. If not defined
@@ -3374,7 +3328,7 @@ Low Level (hardware related) configuration options:
 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
                Option to disable subpage write in NAND driver
                driver that uses this:
-               drivers/mtd/nand/davinci_nand.c
+               drivers/mtd/nand/raw/davinci_nand.c
 
 Freescale QE/FMAN Firmware Support:
 -----------------------------------