+# SPDX-License-Identifier: GPL-2.0+
#
# (C) Copyright 2000 - 2013
# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
Summary:
========
- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
-- Marvell Family Member
- CONFIG_SYS_MVFS - define it if you want to enable
- multiple fs option at one time
- for marvell soc family
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
CONFIG_AT91_HW_WDT_TIMEOUT
specify the timeout in seconds. default 2 seconds.
-- U-Boot Version:
- CONFIG_VERSION_VARIABLE
- If this variable is defined, an environment variable
- named "ver" is created by U-Boot showing the U-Boot
- version as printed by the "version" command.
- Any change to this variable will be reverted at the
- next reset.
-
- Real-Time Clock:
When CONFIG_CMD_DATE is selected, the type of the RTC
CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
bootloader. Note 2TB partition limit; see
disk/part_efi.c
- CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
-
- If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
CONFIG_SUPPORT_EMMC_BOOT
Enable some additional features of the eMMC boot partitions.
- CONFIG_SUPPORT_EMMC_RPMB
- Enable the commands for reading, writing and programming the
- key for the Replay Protection Memory Block partition in eMMC.
-
- USB Device Firmware Update (DFU) class support:
CONFIG_DFU_OVER_USB
This enables the USB portion of the DFU USB class
the environment like the "source" command or the
boot command first.
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-
- Define this in order to add variables describing certain
- run-time determined information about the hardware to the
- environment. These will be named board_name, board_rev.
-
CONFIG_DELAY_ENVIRONMENT
Normally the environment is loaded when the board is
-150 common/cmd_nand.c Incorrect FIT image format
151 common/cmd_nand.c FIT image format OK
-- legacy image format:
- CONFIG_IMAGE_FORMAT_LEGACY
- enables the legacy image format support in U-Boot.
-
- Default:
- enabled if CONFIG_FIT_SIGNATURE is not defined.
-
- CONFIG_DISABLE_IMAGE_LEGACY
- disable the legacy image format
-
- This define is introduced, as the legacy image format is
- enabled per default for backward compatibility.
-
- Standalone program support:
CONFIG_STANDALONE_LOAD_ADDR
for a more detailed description refer to doc/README.update.
- MTD Support (mtdparts command, UBI support)
- CONFIG_MTD_DEVICE
-
- Adds the MTD device infrastructure from the Linux kernel.
- Needed for mtdparts command support.
-
- CONFIG_MTD_PARTITIONS
-
- Adds the MTD partitioning infrastructure from the Linux
- kernel. Needed for UBI support.
-
-- UBI support
CONFIG_MTD_UBI_WL_THRESHOLD
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
CONFIG_SPL_NAND_DRIVERS
SPL uses normal NAND drivers, not minimal drivers.
+ CONFIG_SPL_NAND_IDENT
+ SPL uses the chip ID list to identify the NAND flash.
+ Requires CONFIG_SPL_NAND_BASE.
+
CONFIG_SPL_NAND_ECC
Include standard software ECC in the SPL
use an arch-specific makefile fragment instead, for
example if more than one image needs to be produced.
- CONFIG_FIT_SPL_PRINT
+ CONFIG_SPL_FIT_PRINT
Printing information about a FIT image adds quite a bit of
code to SPL. So this is normally disabled in SPL. Use this
option to re-enable it. This will affect the output of the
Begin and End addresses of the area used by the
simple memory test.
-- CONFIG_SYS_ALT_MEMTEST:
- Enable an alternate, more extensive memory test.
-
- CONFIG_SYS_MEMTEST_SCRATCH:
Scratch address used by the alternate memory test
You only need to set this if address zero isn't writeable
regular expression. This allows multiple variables to be connected to
the same callback without explicitly listing them all out.
+The signature of the callback functions is:
+
+ int callback(const char *name, const char *value, enum env_op op, int flags)
+
+* name - changed environment variable
+* value - new value of the environment variable
+* op - operation (create, overwrite, or delete)
+* flags - attributes of the environment variable change, see flags H_* in
+ include/search.h
+
+The return value is 0 if the variable change is accepted and 1 otherwise.
Command Line Parsing:
=====================
projects / oweals / u-boot.git / blobdiff