- Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
-- Marvell Family Member
- CONFIG_SYS_MVFS - define it if you want to enable
- multiple fs option at one time
- for marvell soc family
-
- 85xx CPU Options:
CONFIG_SYS_PPC64
pointer. This is needed for the temporary stack before
relocation.
- CONFIG_SYS_MIPS_CACHE_MODE
-
- Cache operation mode for the MIPS CPU.
- See also arch/mips/include/asm/mipsregs.h.
- Possible values are:
- CONF_CM_CACHABLE_NO_WA
- CONF_CM_CACHABLE_WA
- CONF_CM_UNCACHED
- CONF_CM_CACHABLE_NONCOHERENT
- CONF_CM_CACHABLE_CE
- CONF_CM_CACHABLE_COW
- CONF_CM_CACHABLE_CUW
- CONF_CM_CACHABLE_ACCELERATED
-
- CONFIG_SYS_XWAY_EBU_BOOTCFG
-
- Special option for Lantiq XWAY SoCs for booting from NOR flash.
- See also arch/mips/cpu/mips32/start.S.
-
CONFIG_XWAY_SWAP_BYTES
Enable compilation of tools/xway-swap-bytes needed for Lantiq
CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
bootloader. Note 2TB partition limit; see
disk/part_efi.c
- CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
-
- If IDE or SCSI support is enabled (CONFIG_IDE or
CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
Define this to use i/o functions instead of macros
(some hardware wont work with macros)
- CONFIG_DRIVER_TI_EMAC
- Support for davinci emac
-
CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
Define this if you have more then 3 PHYs.
for a more detailed description refer to doc/README.update.
- MTD Support (mtdparts command, UBI support)
- CONFIG_MTD_DEVICE
-
- Adds the MTD device infrastructure from the Linux kernel.
- Needed for mtdparts command support.
-
- CONFIG_MTD_PARTITIONS
-
- Adds the MTD partitioning infrastructure from the Linux
- kernel. Needed for UBI support.
-
-- UBI support
CONFIG_MTD_UBI_WL_THRESHOLD
This parameter defines the maximum difference between the highest
erase counter value and the lowest erase counter value of eraseblocks
CONFIG_SPL_NAND_DRIVERS
SPL uses normal NAND drivers, not minimal drivers.
+ CONFIG_SPL_NAND_IDENT
+ SPL uses the chip ID list to identify the NAND flash.
+ Requires CONFIG_SPL_NAND_BASE.
+
CONFIG_SPL_NAND_ECC
Include standard software ECC in the SPL
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_USE_STDINT
- If stdint.h is available with your toolchain you can define this
- option to enable it. You can provide option 'USE_STDINT=1' when
- building U-Boot to enable this.
-
The following definitions that deal with the placement and management
of environment data (variable area); in general, we support the
following configurations:
a 16 bit bus.
Not all NAND drivers use this symbol.
Example of drivers that use it:
- - drivers/mtd/nand/ndfc.c
- - drivers/mtd/nand/mxc_nand.c
+ - drivers/mtd/nand/raw/ndfc.c
+ - drivers/mtd/nand/raw/mxc_nand.c
- CONFIG_SYS_NDFC_EBC0_CFG
Sets the EBC0_CFG register for the NDFC. If not defined
- CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
Option to disable subpage write in NAND driver
driver that uses this:
- drivers/mtd/nand/davinci_nand.c
+ drivers/mtd/nand/raw/davinci_nand.c
Freescale QE/FMAN Firmware Support:
-----------------------------------
regular expression. This allows multiple variables to be connected to
the same callback without explicitly listing them all out.
+The signature of the callback functions is:
+
+ int callback(const char *name, const char *value, enum env_op op, int flags)
+
+* name - changed environment variable
+* value - new value of the environment variable
+* op - operation (create, overwrite, or delete)
+* flags - attributes of the environment variable change, see flags H_* in
+ include/search.h
+
+The return value is 0 if the variable change is accepted and 1 otherwise.
Command Line Parsing:
=====================