dm: clk: Define clk_get_parent() for clk operations

[oweals/u-boot.git] / README

diff --git a/README b/README
index 6525b81e3f83a25cc74995e0c02ad08fd20cb9e9..8f816ad2aff4d141e689dba5adbf5945cdf358b2 100644 (file)
--- a/README
+++ b/README
@@ -486,10 +486,6 @@ The following options need to be configured:
                PBI commands can be used to configure SoC before it starts the execution.
                Please refer doc/README.pblimage for more details
 
-               CONFIG_SPL_FSL_PBL
-               It adds a target to create boot binary having SPL binary in PBI format
-               concatenated with u-boot binary.
-
                CONFIG_SYS_FSL_DDR_BE
                Defines the DDR controller register space as Big Endian
 
@@ -634,8 +630,6 @@ The following options need to be configured:
                the defaults discussed just above.
 
 - Cache Configuration:
-               CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
-               CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
                CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
 
 - Cache Configuration for ARM:
@@ -767,9 +761,6 @@ The following options need to be configured:
                SoC, then define this variable and provide board
                specific code for the "hw_watchdog_reset" function.
 
-               CONFIG_AT91_HW_WDT_TIMEOUT
-               specify the timeout in seconds. default 2 seconds.
-
 - Real-Time Clock:
 
                When CONFIG_CMD_DATE is selected, the type of the RTC
@@ -1123,9 +1114,6 @@ The following options need to be configured:
                        CONFIG_SH_MMCIF_CLK
                        Define the clock frequency for MMCIF
 
-               CONFIG_SUPPORT_EMMC_BOOT
-               Enable some additional features of the eMMC boot partitions.
-
 - USB Device Firmware Update (DFU) class support:
                CONFIG_DFU_OVER_USB
                This enables the USB portion of the DFU USB class
@@ -2130,21 +2118,6 @@ The following options need to be configured:
                this is instead controlled by the value of
                /config/load-environment.
 
-- Serial Flash support
-               Usage requires an initial 'sf probe' to define the serial
-               flash parameters, followed by read/write/erase/update
-               commands.
-
-               The following defaults may be provided by the platform
-               to handle the common case when only a single serial
-               flash is present on the system.
-
-               CONFIG_SF_DEFAULT_BUS           Bus identifier
-               CONFIG_SF_DEFAULT_CS            Chip-select
-               CONFIG_SF_DEFAULT_MODE          (see include/spi.h)
-               CONFIG_SF_DEFAULT_SPEED         in Hz
-
-
 - TFTP Fixed UDP Port:
                CONFIG_TFTP_PORT
 
@@ -2441,9 +2414,6 @@ FIT uImage format:
                When defined, the linker checks that the actual size does
                not exceed it.
 
-               CONFIG_SPL_TEXT_BASE
-               TEXT_BASE for linking the SPL binary.
-
                CONFIG_SPL_RELOC_TEXT_BASE
                Address to relocate to.  If unspecified, this is equal to
                CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
@@ -2572,9 +2542,6 @@ FIT uImage format:
                Defines the size and behavior of the NAND that SPL uses
                to read U-Boot
 
-               CONFIG_SPL_NAND_BOOT
-               Add support NAND boot
-
                CONFIG_SYS_NAND_U_BOOT_OFFS
                Location in NAND to read U-Boot from
 
@@ -3320,12 +3287,12 @@ within that device.
 
 - CONFIG_SYS_FMAN_FW_ADDR
        The address in the storage device where the FMAN microcode is located.  The
-       meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+       meaning of this address depends on which CONFIG_SYS_QE_FMAN_FW_IN_xxx macro
        is also specified.
 
 - CONFIG_SYS_QE_FW_ADDR
        The address in the storage device where the QE microcode is located.  The
-       meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
+       meaning of this address depends on which CONFIG_SYS_QE_FMAN_FW_IN_xxx macro
        is also specified.
 
 - CONFIG_SYS_QE_FMAN_FW_LENGTH