Configuration Settings:
-----------------------
-- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+- MEM_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
Optionally it can be defined to support 64-bit memory commands.
- CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
forced to a value that ensures that CCSR is not relocated.
-- Floppy Disk Support:
- CONFIG_SYS_FDC_DRIVE_NUMBER
-
- the default drive number (default value 0)
-
- CONFIG_SYS_ISA_IO_STRIDE
-
- defines the spacing between FDC chipset registers
- (default value 1)
-
- CONFIG_SYS_ISA_IO_OFFSET
-
- defines the offset of register from address. It
- depends on which part of the data bus is connected to
- the FDC chipset. (default value 0)
-
- If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
- CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
- default value.
-
- if CONFIG_SYS_FDC_HW_INIT is defined, then the function
- fdc_hw_init() is called at the beginning of the FDC
- setup. fdc_hw_init() must be provided by the board
- source code. It is used to make hardware-dependent
- initializations.
-
- CONFIG_IDE_AHB:
Most IDE controllers were designed to be connected with PCI
interface. Only few of them were designed for AHB interface.
- CONFIG_SYS_SRIOn_MEM_VIRT:
Virtual Address of SRIO port 'n' memory region
-- CONFIG_SYS_SRIOn_MEM_PHYS:
+- CONFIG_SYS_SRIOn_MEM_PHYxS:
Physical Address of SRIO port 'n' memory region
- CONFIG_SYS_SRIOn_MEM_SIZE:
Add the "loopw" memory command. This only takes effect if
the memory commands are activated globally (CONFIG_CMD_MEMORY).
-- CONFIG_MX_CYCLIC
+- CONFIG_CMD_MX_CYCLIC
Add the "mdc" and "mwc" memory commands. These are cyclic
"md/mw" commands.
Examples:
instruction cache) is still performed.
- CONFIG_SPL_BUILD
- Modifies the behaviour of start.S when compiling a loader
- that is executed before the actual U-Boot. E.g. when
- compiling a NAND SPL.
+ Set when the currently-running compilation is for an artifact
+ that will end up in the SPL (as opposed to the TPL or U-Boot
+ proper). Code that needs stage-specific behavior should check
+ this.
- CONFIG_TPL_BUILD
- Modifies the behaviour of start.S when compiling a loader
- that is executed after the SPL and before the actual U-Boot.
- It is loaded by the SPL.
+ Set when the currently-running compilation is for an artifact
+ that will end up in the TPL (as opposed to the SPL or U-Boot
+ proper). Code that needs stage-specific behavior should check
+ this.
- CONFIG_SYS_MPC85XX_NO_RESETVEC
Only for 85xx systems. If this variable is specified, the section
If you have modified U-Boot sources (for instance added a new board
or support for new devices, a new CPU, etc.) you are expected to
provide feedback to the other developers. The feedback normally takes
-the form of a "patch", i. e. a context diff against a certain (latest
+the form of a "patch", i.e. a context diff against a certain (latest
official or latest in the git repository) version of U-Boot sources.
But before you submit such a patch, please verify that your modifi-