patman: Update flushing Print() for Python 3

[oweals/u-boot.git] / README

diff --git a/README b/README
index 91dfb24776e185986788603ad055da9d218a689b..7ebf9f577e6defe2860da1348b3b06ffa4081b0e 100644 (file)
--- a/README
+++ b/README
@@ -2460,7 +2460,7 @@ typically in board_init_f() and board_init_r().
 Configuration Settings:
 -----------------------
 
-- CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
+- MEM_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
                Optionally it can be defined to support 64-bit memory commands.
 
 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
@@ -2870,32 +2870,6 @@ Low Level (hardware related) configuration options:
                If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
                forced to a value that ensures that CCSR is not relocated.
 
-- Floppy Disk Support:
-               CONFIG_SYS_FDC_DRIVE_NUMBER
-
-               the default drive number (default value 0)
-
-               CONFIG_SYS_ISA_IO_STRIDE
-
-               defines the spacing between FDC chipset registers
-               (default value 1)
-
-               CONFIG_SYS_ISA_IO_OFFSET
-
-               defines the offset of register from address. It
-               depends on which part of the data bus is connected to
-               the FDC chipset. (default value 0)
-
-               If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
-               CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
-               default value.
-
-               if CONFIG_SYS_FDC_HW_INIT is defined, then the function
-               fdc_hw_init() is called at the beginning of the FDC
-               setup. fdc_hw_init() must be provided by the board
-               source code. It is used to make hardware-dependent
-               initializations.
-
 - CONFIG_IDE_AHB:
                Most IDE controllers were designed to be connected with PCI
                interface. Only few of them were designed for AHB interface.
@@ -3051,7 +3025,7 @@ Low Level (hardware related) configuration options:
                Add the "loopw" memory command. This only takes effect if
                the memory commands are activated globally (CONFIG_CMD_MEMORY).
 
-- CONFIG_MX_CYCLIC
+- CONFIG_CMD_MX_CYCLIC
                Add the "mdc" and "mwc" memory commands. These are cyclic
                "md/mw" commands.
                Examples:
@@ -3229,9 +3203,9 @@ is done by typing:
        make NAME_defconfig
 
 where "NAME_defconfig" is the name of one of the existing configu-
-rations; see boards.cfg for supported names.
+rations; see configs/*_defconfig for supported names.
 
-Note: for some board special configuration names may exist; check if
+Note: for some boards special configuration names may exist; check if
       additional information is available from the board vendor; for
       instance, the TQM823L systems are available without (standard)
       or with LCD support. You can select such additional "features"
@@ -4665,7 +4639,7 @@ int main(int argc, char *argv[])
        while (learning) {
                Read the README file in the top level directory;
                Read http://www.denx.de/twiki/bin/view/DULG/Manual;
-               Read applicable doc/*.README;
+               Read applicable doc/README.*;
                Read the source, Luke;
                /* find . -name "*.[chS]" | xargs grep -i <keyword> */
        }
@@ -4760,8 +4734,6 @@ it:
 * For new features: a description of the feature and your
   implementation.
 
-* A CHANGELOG entry as plaintext (separate from the patch)
-
 * For major contributions, add a MAINTAINERS file with your
   information and associated file and directory references.