fs: Fully populate the filesystem method struct

[oweals/u-boot.git] / README

diff --git a/README b/README
index 8707bf2d7c4510872feaf5e527c230d0919e28bb..51eb71b27c5de9015bd7676f79930b6c16fb2a75 100644 (file)
--- a/README
+++ b/README
@@ -842,7 +842,8 @@ The following options need to be configured:
                CONFIG_CMD_I2C          * I2C serial bus support
                CONFIG_CMD_IDE          * IDE harddisk support
                CONFIG_CMD_IMI            iminfo
-               CONFIG_CMD_IMLS           List all found images
+               CONFIG_CMD_IMLS           List all images found in NOR flash
+               CONFIG_CMD_IMLS_NAND      List all images found in NAND flash
                CONFIG_CMD_IMMAP        * IMMR dump support
                CONFIG_CMD_IMPORTENV    * import an environment
                CONFIG_CMD_INI          * import data from an ini file into the env
@@ -2714,10 +2715,13 @@ FIT uImage format:
                CONFIG_FB_ADDR
 
                Define CONFIG_FB_ADDR if you want to use specific
-               address for frame buffer.
-               Then system will reserve the frame buffer address to
-               defined address instead of lcd_setmem (this function
-               grabs the memory for frame buffer by panel's size).
+               address for frame buffer.  This is typically the case
+               when using a graphics controller has separate video
+               memory.  U-Boot will then place the frame buffer at
+               the given address instead of dynamically reserving it
+               in system RAM by calling lcd_setmem(), which grabs
+               the memory for the frame buffer depending on the
+               configured panel size.
 
                Please see board_init_f function.
 
@@ -2816,6 +2820,12 @@ FIT uImage format:
                CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME
                Filename to read to load U-Boot when reading from FAT
 
+               CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
+               Set this for NAND SPL on PPC mpc83xx targets, so that
+               start.S waits for the rest of the SPL to load before
+               continuing (the hardware starts execution after just
+               loading the first page rather than the full 4K).
+
                CONFIG_SPL_NAND_BASE
                Include nand_base.c in the SPL.  Requires
                CONFIG_SPL_NAND_DRIVERS.
@@ -2873,6 +2883,10 @@ FIT uImage format:
                CONFIG_SPL_LIBGENERIC_SUPPORT
                Support for lib/libgeneric.o in SPL binary
 
+               CONFIG_SPL_PAD_TO
+               Linker address to which the SPL should be padded before
+               appending the SPL payload.
+
                CONFIG_SPL_TARGET
                Final target image containing SPL and payload.  Some SPLs
                use an arch-specific makefile fragment instead, for
@@ -3797,20 +3811,24 @@ Low Level (hardware related) configuration options:
                that is executed before the actual U-Boot. E.g. when
                compiling a NAND SPL.
 
+- CONFIG_ARCH_MAP_SYSMEM
+               Generally U-Boot (and in particular the md command) uses
+               effective address. It is therefore not necessary to regard
+               U-Boot address as virtual addresses that need to be translated
+               to physical addresses. However, sandbox requires this, since
+               it maintains its own little RAM buffer which contains all
+               addressable memory. This option causes some memory accesses
+               to be mapped through map_sysmem() / unmap_sysmem().
+
 - CONFIG_USE_ARCH_MEMCPY
   CONFIG_USE_ARCH_MEMSET
                If these options are used a optimized version of memcpy/memset will
                be used if available. These functions may be faster under some
                conditions but may increase the binary size.
 
-- CONFIG_X86_NO_RESET_VECTOR
-               If defined, the x86 reset vector code is excluded. You will need
-               to do this when U-Boot is running from Coreboot.
-
-- CONFIG_X86_NO_REAL_MODE
-               If defined, x86 real mode code is omitted. This assumes a
-               32-bit environment where such code is not needed. You will
-               need to do this when U-Boot is running from Coreboot.
+- CONFIG_X86_RESET_VECTOR
+               If defined, the x86 reset vector code is included. This is not
+               needed when U-Boot is running from Coreboot.
 
 
 Freescale QE/FMAN Firmware Support: