'Sane' compilers will generate smaller code if
CONFIG_PRE_CON_BUF_SZ is a power of 2
-- Boot Delay: CONFIG_BOOTDELAY - in seconds
- Delay before automatically booting the default image;
- set to -1 to disable autoboot.
- set to -2 to autoboot with no delay and not check for abort
- (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
-
- See doc/README.autoboot for these options that
- work with CONFIG_BOOTDELAY. None are required.
- CONFIG_BOOT_RETRY_TIME
- CONFIG_BOOT_RETRY_MIN
- CONFIG_AUTOBOOT_KEYED
- CONFIG_AUTOBOOT_PROMPT
- CONFIG_AUTOBOOT_DELAY_STR
- CONFIG_AUTOBOOT_STOP_STR
- CONFIG_ZERO_BOOTDELAY_CHECK
- CONFIG_RESET_TO_RETRY
-
- Autoboot Command:
CONFIG_BOOTCOMMAND
Only needed when CONFIG_BOOTDELAY is enabled;
CONFIG_CMD_ECHO echo arguments
CONFIG_CMD_EDITENV edit env variable
CONFIG_CMD_EEPROM * EEPROM read/write support
+ CONFIG_CMD_EEPROM_LAYOUT* EEPROM layout aware commands
CONFIG_CMD_ELF * bootelf, bootvx
CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
CONFIG_CMD_ENV_FLAGS * display details about env flags
CONFIG_CMD_RUN run command in env variable
CONFIG_CMD_SANDBOX * sb command to access sandbox features
CONFIG_CMD_SAVES * save S record dump
- CONFIG_CMD_SCSI * SCSI Support
+ CONFIG_SCSI * SCSI Support
CONFIG_CMD_SDRAM * print SDRAM configuration information
(requires CONFIG_CMD_I2C)
CONFIG_CMD_SETGETDCR Support for DCR Register access
XXX - this list needs to get updated!
+- Removal of commands
+ If no commands are needed to boot, you can disable
+ CONFIG_CMDLINE to remove them. In this case, the command line
+ will not be available, and when U-Boot wants to execute the
+ boot command (on start-up) it will call board_run_command()
+ instead. This can reduce image size significantly for very
+ simple boot procedures.
+
- Regular expression support:
CONFIG_REGEX
If this variable is defined, U-Boot is linked against
CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
- CONFIG_CMD_SCSI) you must configure support for at
+ CONFIG_SCSI) you must configure support for at
least one non-MTD partition type as well.
- IDE Reset method:
The DIU driver will look for the 'video-mode' environment
variable, and if defined, enable the DIU as a console during
- boot. See the documentation file README.video for a
+ boot. See the documentation file doc/README.video for a
description of this variable.
- LCD Support: CONFIG_LCD
If this option is set, then U-Boot will prevent the environment
variable "splashimage" from being set to a problematic address
- (see README.displaying-bmps).
+ (see doc/README.displaying-bmps).
This option is useful for targets where, due to alignment
restrictions, an improperly aligned BMP image will cause a data
abort. If you think you will not have problems with unaligned
consider that a completely unreadable NAND block is bad,
and thus should be skipped silently.
+ CONFIG_SPL_ABORT_ON_RAW_IMAGE
+ When defined, SPL will proceed to another boot method
+ if the image it has loaded does not have a signature.
+
CONFIG_SPL_RELOC_STACK
Adress of the start of the stack SPL will use after
relocation. If unspecified, this is equal to
If defined, don't allow the -f switch to env set override variable
access flags.
-- CONFIG_SYS_GENERIC_BOARD
- This selects the architecture-generic board system instead of the
- architecture-specific board files. It is intended to move boards
- to this new framework over time. Defining this will disable the
- arch/foo/lib/board.c file and use common/board_f.c and
- common/board_r.c instead. To use this option your architecture
- must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig).
- If you find problems enabling this option on your board please report
- the problem and send patches!
-
- CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
This is set by OMAP boards for the max time that reset should
be asserted. See doc/README.omap-reset-time for details on how
other boot loader or by a debugger which performs
these initializations itself.
+- CONFIG_SKIP_LOWLEVEL_INIT_ONLY
+ [ARM926EJ-S only] This allows just the call to lowlevel_init()
+ to be skipped. The normal CPU15 init (such as enabling the
+ instruction cache) is still performed.
+
- CONFIG_SPL_BUILD
Modifies the behaviour of start.S when compiling a loader
that is executed before the actual U-Boot. E.g. when
projects / oweals / u-boot.git / blobdiff