Changes since U-Boot 1.1.4:
======================================================================
+* Several improvements to the new NAND subsystem:
+ - JFFS2 related commands implemented in mtd-utils style
+ - Support for bad blocks
+ - Bad block testing commands
+ - NAND lock commands
+ Please take a look at doc/README.nand for more details
+ Patch by Guido Classen, 10 Oct 2006
+
+* Define IH_CPU_AVR32
+ Make it possible to generate AVR32 uImage files with mkimage and
+ make cmd_bootm recognize them.
+ Patch by Haavard Skinnemoen, 22 Sep 2006
+
+* Fix buffer overflow problem in ft_build.c
+ Patch by Fredrik Roubert, 09 Oct 2006
+
+* Make bootp implementation RFC3046 compliant
+ Patch by Joakim Larsson, 27 Jun 2006
+
+* TQM5200: perform POST memory test only on STK52xx carrier board.
+ (and then only if PSC6_3 is read as "1" when booting).
+ Patch by Martin Krause, 21 Jun 2006
+
+* Move "ar" flags to config.mk to allow for silent "make -s"
+ Based on patch by Mike Frysinger, 20 Jun 2006
+
+* Coding style cleanup
+
+* Add support for EP82xxM boards
+ Patch by Aaron Sells, 20 Jun 2006
+
+* Fix comments in include/ppc440.h
+ Patch by Martin Hicks, 16 Jun 2006
+
+* Update for CAM5200 board:
+ - Map in a additional chip selects CS4 and CS5.
+ - Modify the port configration, configure six UARTs and no PCI,
+ ATA and USB.
+ - Add custom flash driver to handle specific byte swapping
+
+* Fix TLB setup for Ocotea board
+ Patch by Stefan Roese, 30 Sep 2006
+
+* Fix reset problem in sequoia sdram init code
+ Patch by Stefan Roese, 23 Sep 2006
+
+* Disable autoboot abort for FO300 when silent mode is enabled
+ (according to S1 switch setting).
+
+* Cleanup examples binaries
+
+* Add support for AMCC Rainier PPX440GRx eval board
+ Patch by Stefan Roese, 13 Sep 2006
+
+* Add NAND environment support for PPC440EPx Sequoia NAND boot config
+ Patch by Stefan Roese, 12 Sep 2006
+
+* Update NAND boot documentation
+ Patch by Stefan Roese, 12 Sep 2006
+
+* Fix alignment problem in "mtdparts" command
+
+* Add documentation on the latest build environment extensions to
+ the README file.
+
+* Remove dead code (i2o and dma) from cpu/mpc824x/drivers/ directory.
+
+* Fix LOG_DIR directory creation error.
+ Add support for automatic creation of BUILD_DIR directory.
+
+* Fix build problem cpu/ppc4xx/ndfc.c
+ Patch by Stefan Roese, 07 Sep 2006
+
+* Fix build problem with CPCI440
+ Patch by Stefan Roese, 07 Sep 2006
+
+* Change Yellowstone to use CFI write buffer
+ Patch by Stefan Roese, 07 Sep 2006
+
+* Add support for AMCC Sequoia PPC440EPx eval board
+ - Add support for PPC440EPx & PPC440GRx
+ - Add support for PPC440EP(x)/GR(x) NAND controller
+ in cpu/ppc4xx directory
+ - Add NAND boot functionality for Sequoia board,
+ please see doc/README.nand-boot-ppc440 for details
+ - This Sequoia NAND image doesn't support environment
+ in NAND for now. This will be added in a short while.
+ Patch by Stefan Roese, 07 Sep 2006
+
+* Fix mkimage -l bug with multifile images on 64bit platforms
+ Patch by David Updegraff, 06 Sep 2006
+
+* Fix build problems on sorcery board.
+
+* Fix coldfire build problems.
+ Patch by Marian Balakowicz, 01 Sep 2006
+
+* Add support for a saving build objects in a separate directory.
+ Modifications are based on the Linux kernel approach and support
+ two use cases:
+ 1) Add O= to the make command line 'make O=/tmp/build all'
+ 2) Set environement variable BUILD_DIR to point to the desired location
+ 'export BUILD_DIR=/tmp/build'
+ 'make'
+ The second approach can also be used with a MAKEALL script
+ 'export BUILD_DIR=/tmp/build'
+ './MAKEALL'
+ Command line 'O=' setting overrides the BUILD_DIR environent variable.
+ When none of the above methods is used the local build is performed
+ and the object files are placed in the source directory.
+
+* Remove the board/netstar/crcit binary from git repository.
+
+* Fix tools/updater build error.
+
+* Fix tools/easylogo build error.
+
+* Fixed problems on PRS200 board caused by adding splash screen on MCC200
+
+* Extended README entry on coding style
+
+* Added another example showing simple interrupt interception.
+
+* Added simple_strtoul(), getenv() and setenv() to the exported functions.
+ Also bumped up ABI version to reflect this change.
+
+* Added interrupt handling capabilities for mpc5xxx processors.
+ Also added Linux like BUG() macros.
+
+* Coding Style cleanup.
+ Patch by Stefano Babic, 31 Aug 2006
+
+* Add splashscreen support for MCC200 board.
+
+* Make the serial driver framework work with CONFIG_SERIAL_MULTI
+ enabled
+
+* PCIe endpoint support for AMCC Yucca 440SPe board
+ Patch by Tirumala R Marri, 26 Aug 2006
+
+* Improve DIMM detection for AMCC Yucca 440SPe board
+ Improved the memory DIMM detection for the Yucca 440SPe board for
+ the case where a memory DIMM is falsely detected as present.
+ This issue is seen on some AMCC Yucca 440SPe validation boards if
+ only one 512MB memory DIMM is installed, i.e. DIMM slot 0 is
+ populated and DIMM slot 1 is empty. In this case, U-Boot does
+ not correctly detect that there is only one DIMM memory module
+ installed and will falsely detect two DIMM memory modules are
+ present and therefore U-Boot will not calculate the correct amount
+ of total memory and u-boot will not booting up.
+ Patch by Adam Graham, 24 Aug 2006
+
+* Fix typo.
+
+* Code cleanup
+
+* Update for MCC200 / PRS200 boards:
+ - auto-adjust console device for Linux.
+ - fix typos.
+
+* Add a fix for a buggy USB device on the FO300 board.
+
+* Updates for MCC200 / PRS200 boards:
+ - support for configurations with SDRAM or DDR memory,
+ - support for highboot and lowboot
+ - adjusting environment definitions
+
+* Add support for WTK FO300 board (TQM5200 based).
+
+* Fix TQM834x hang.
+
+* Update for SC520 board.
+ Patch by David Updegraff, 02 Dec 2005
+
+* Fixed common.h spelling error.
+ Patch by Cory Tusar, 30 Nov 2005
+
+* Fix typo.
+ Patch by Andreas Engel, 28 Nov 2005
+
+* Fix fatload command on FAT32 formatted partitions.
+ Patch by Joachim Jaeger, 18 Nov 2005
+
+* Fix drivers/dm9000.c when configured in 32 bit mode.
+ Patch by Eric Benard, 17 Nov 2005
+
+* Cleanup debug code for yucca board.
+
+* MCC200: restrict addressable flash space to 32 MB
+
+* Add debug console on COM12 for MCC200 board
+
+* Fix control-c handing in CONFIG_CMDLINE_EDITING
+ Properly pass break code back from readline.
+ Patch by Roger Blofeld, 31 Jul 2006
+
+* Add commandline history support to all AMCC eval boards
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Add Macronix MXLV320T flash support for AMCC Bamboo
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Change "mii info" to not print an error upon missing PHY at address
+ Patch by Stefan Roese, 07 Aug 2006
+
+* Fix PCI-Express on PPC440SPe rev. A.
+
+* Fix preboot message on TQM85xx after switching to hush parser.
+
+* Adapt TQM85xx ramdisk address to Linux kernel memory map
+
+* Add initial support for PCI-Express on PPC440SPe (Yucca board).
+
+* Fix compiler warning for TRAB board.
+ Patch by Martin Krause, 07 Aug 2006
+
+* Prevent USB commands from working when USB is stopped.
+
+* Add rudimentary handling of alternate settings of USB interfaces.
+ This is in order to fix issues with some USB sticks timing out
+ during initialization. Some code readability improvements.
+
+* PPC440 DDR setup: Set SDRAM0_CFG0[PMU]=0 for best performance
+ AMCC suggested to set the PMU bit to 0 for best performace on
+ the PPC440 DDR controller.
+ Please see doc/README.440-DDR-performance for details.
+ Patch by Stefan Roese, 28 Jul 2006
+
+* AMCC bamboo (440EP) U-Boot image reduced to 384kbyte
+ Please see doc/README.bamboo for details.
+ Patch by Stefan Roese, 27 Jul 2006
+
+* Fix CONFIG_CMDLINE_EDITING implementation
+ Patch by Stefan Roese, 27 Jul 2006
+
+* Fix preboot message on TQM5200 after switching to hush parser.
+
+* MCC200: set default configuration to low_boot DDR,
+ and support for configurable options high_boot and/or SDRAM.
+
+* Add support for 256 MB SDRAM on CPU87
+ Patch by Josef Wagner, 25 Nov 2005
+
+* Add configuration for cam5200 board (based on TQM5200S).
+
+* More code cleanup
+
+* Disabled kvme080 board in MAKEALL because of build problems.
+
+* Code cleanup
+
+* Update NetStar board
+ Patch by Ladislav Michl, 03 Nov 2005
+
+* Make code better readable.
+ Patch by Ladislav Michl, 14 Sep 2005
+
+* Enable initrd ATAG for xm250 board.
+ Patch by Josef Wagner, 05 Sep 2005
+
+* Add readline cmdline-editing extension
+ Patch by JinHua Luo, 01 Sep 2005
+
* Add support for friendly-arm SBC-2410X board
Patch by JinHua Luo, 01 Sep 2005
-
+
* Fix multi-part image support on i386 platform.
Patch by David Updegraff, 19 Aug 2005