Changes since U-Boot 1.1.4:
======================================================================
+* Changes/fixes for drivers/cfi_flash.c:
+
+ - Add Intel legacy lock/unlock support to common CFI driver
+
+ On some Intel flash's (e.g. Intel J3) legacy unlocking is
+ supported, meaning that unlocking of one sector will unlock
+ all sectors of this bank. Using this feature, unlocking
+ of all sectors upon startup (via env var "unlock=yes") will
+ get much faster.
+
+ - Fixed problem with multiple reads of envronment variable
+ "unlock" as pointed out by Reinhard Arlt & Anders Larsen.
+
+ - Removed unwanted linefeeds from "protect" command when
+ CFG_FLASH_PROTECTION is enabled.
+
+ - Changed p3p400 board to use CFG_FLASH_PROTECTION
+
+ Patch by Stefan Roese, 01 Apr 2006
+
+* Changes/fixes for drivers/cfi_flash.c:
+ - Correctly handle the cases where CFG_HZ != 1000 (several
+ XScale-based boards)
+ - Fix the timeout calculation of buffered writes (off by a
+ factor of 1000)
+ Patch by Anders Larsen, 31 Mar 2006
+
+* Updates to common PPC4xx onboard (DDR)SDRAM init code (405 and 440)
+
+ 405 SDRAM: - The SDRAM parameters can now be defined in the board
+ config file and the 405 SDRAM controller values will
+ be calculated upon bootup (see PPChameleonEVB).
+ When those settings are not defined in the board
+ config file, the register setup will be as it is now,
+ so this implementation should not break any current
+ design using this code.
+
+ Thanks to Andrea Marson from DAVE for this patch.
+
+ 440 DDR: - Added function sdram_tr1_set to auto calculate the
+ TR1 value for the DDR.
+ - Added ECC support (see p3p440).
+
+ Patch by Stefan Roese, 17 Mar 2006
+
+* Fix CONFIG_SKIP_LOWLEVEL_INIT dependency in cpu/arm920t/start.S
+ Patch by Peter Menzebach, 13 Oct 2005 [DNX#2006040142000473]
+
+* Add support for ymodem protocol download
+ Patch by Stefano Babic, 29 Mar 2006
+
+* Memory Map Update for Delta board: U-Boot is at 0x80000000-0x84000000
+ Merge from Markus Klotzbücher's repo, 01 Apr 2006
+
+* GCC-4.x fixes: clean up global data pointer initialization for all
+ boards
+
+* Update for Delta board:
+ - redundant NAND environment
+ - misc Monahans cleanups (remove dead code etc.)
+ - DA9030 Initialization; some minimal changes to PXA I2C driver to
+ make it work with the Monahans.
+ - Make Monahans clock frequency configurable using
+ CFG_MONAHANS_RUN_MODE_OSC_RATIO and
+ CFG_MONAHANS_TURBO_RUN_MODE_RATIO.
+ Merge from Markus Klotzbücher's repo, 25 Mar 2006
+
+* Enable Quad UART om MCC200 board.
+
+* Cleanup MCC200 board configuration; omit non-existent stuff.
+
+* Add support for MPC859/866 Rev. A.0
+
+* Add command for handling DDR ECC registers on MPC8349EE MDS board.
+
+* Fix DDR ECC bit definitions for MPC83xx.
+
+* Add initial support for MPC8349E MDS board.
+
+* Add support for ECC DDR initialization on MPC83xx.
+
+* Add DMA support for MPC83xx.
+
+* Add sync in do_reset() routine for MPC83xx after RPR register
+ was written to. It is need on some targets when BAT translation
+ is enabled.
+
+* Add bit definitions for MPC83xx DDR controller registers.
+
+* Add Dcbz(), Dcbi() and Dcbf() routines for MPC83xx.
+
+* Correct shift offsets in icache_status and dcache_status for MPC83xx.
+
+* Add support for DS1374 RTC chip.
+
+* Add support for Lite5200B board.
+ Patch by Patch by Jose Maria (Txema) Lopez, 16 Jan 2006
+
+* Apply SoC concept to arm926ejs CPUs, i.e. move the SoC specific
+ timer and cpu_reset code from cpu/$(CPU) into the new
+ cpu/$(CPU)/$(SOC) directories
+ Patch by Andreas Engel, 13 Mar 2006
+
+* Change max size of uncompressed uImage's to 8MByte and add
+ CFG_BOOTM_LEN to adjust this setting.
+
+ As mentioned by Robin Getz on 2005-05-24 the size of uncompressed
+ uImages was restricted to 4MBytes. This default size is now
+ increased to 8Mbytes and can be overrided by setting CFG_BOOTM_LEN
+ in the board config file.
+
+ Patch by Stefan Roese, 13 Mar 2006
+
+* Fix problem with updated PCI code in cpu/ppc4xx/405gp_pci.c
+ Patch by Stefan Roese, 13 Mar 2006
+
+* cpu/ppc4xx/start.S : exceptions are enabled after relocation
+ Patch by Cedric Vincent, 06 Jul 2005
+
+* au1x00_eth.c: check malloc return value and abort if it failed
+ Patch by Andrew Dyer, 26 Jul 2005
+
* Change the sequence of events in soft_i2c.c:send_ack() to keep from
incorrectly generating start/stop conditions on the bus.
Patch by Andrew Dyer, 26 Jul 2005
projects / oweals / u-boot.git / blobdiff