regmap: Introduce init_range

[oweals/u-boot.git] / drivers / serial / Kconfig

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 2940bd05dc3f939c8e76e9a00dfd4ac6f9e150a6..597db4b9cbba9b644edeedcf01f9483cff23ff47 100644 (file)
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -53,6 +53,16 @@ config SPL_SERIAL_PRESENT
          This option enables the full UART in SPL, so if is it disabled,
          the full UART driver will be omitted, thus saving space.
 
          This option enables the full UART in SPL, so if is it disabled,
          the full UART driver will be omitted, thus saving space.
 

+config TPL_SERIAL_PRESENT
+       bool "Provide a serial driver in TPL"
+       depends on DM_SERIAL
+       default y
+       help
+         In very space-constrained devices even the full UART driver is too
+         large. In this case the debug UART can still be used in some cases.
+         This option enables the full UART in TPL, so if is it disabled,
+         the full UART driver will be omitted, thus saving space.
+

 # Logic to allow us to use the imply keyword to set what the default port
 # should be.  The default is otherwise 1.
 config CONS_INDEX_0
 # Logic to allow us to use the imply keyword to set what the default port
 # should be.  The default is otherwise 1.
 config CONS_INDEX_0


@@ -324,6 +334,15 @@ config DEBUG_UART_MXC
          will need to provide parameters to make this work. The driver will
          be available until the real driver model serial is running.
 
          will need to provide parameters to make this work. The driver will
          be available until the real driver model serial is running.
 

+config DEBUG_UART_SANDBOX
+       bool "sandbox"
+       depends on SANDBOX_SERIAL
+       help
+         Select this to enable the debug UART using the sandbox driver. This
+         provides basic serial output from the console without needing to
+         start up driver model. The driver will be available until the real
+         driver model serial is running.
+

 config DEBUG_UART_STM32
        bool "STMicroelectronics STM32"
        depends on STM32_SERIAL
 config DEBUG_UART_STM32
        bool "STMicroelectronics STM32"
        depends on STM32_SERIAL


@@ -354,6 +373,7 @@ endchoice
 config DEBUG_UART_BASE
        hex "Base address of UART"
        depends on DEBUG_UART
 config DEBUG_UART_BASE
        hex "Base address of UART"
        depends on DEBUG_UART

+       default 0 if DEBUG_UART_SANDBOX

        help
          This is the base address of your UART for memory-mapped UARTs.
 
        help
          This is the base address of your UART for memory-mapped UARTs.
 


@@ -363,6 +383,7 @@ config DEBUG_UART_BASE
 config DEBUG_UART_CLOCK
        int "UART input clock"
        depends on DEBUG_UART
 config DEBUG_UART_CLOCK
        int "UART input clock"
        depends on DEBUG_UART

+       default 0 if DEBUG_UART_SANDBOX

        help
          The UART input clock determines the speed of the internal UART
          circuitry. The baud rate is derived from this by dividing the input
        help
          The UART input clock determines the speed of the internal UART
          circuitry. The baud rate is derived from this by dividing the input


@@ -625,6 +646,23 @@ config MSM_SERIAL
          for example APQ8016 and MSM8916.
          Single baudrate is supported in current implementation (115200).
 
          for example APQ8016 and MSM8916.
          Single baudrate is supported in current implementation (115200).
 

+config OMAP_SERIAL
+       bool "Support for OMAP specific UART"
+       depends on DM_SERIAL
+       default y if (ARCH_OMAP2PLUS || ARCH_K3)
+       select SYS_NS16550
+       help
+         If you have an TI based SoC and want to use the on-chip serial
+         port, say Y to this option. If unsure say N.
+
+config OWL_SERIAL
+       bool "Actions Semi OWL UART"
+       depends on DM_SERIAL && ARCH_OWL
+       help
+         If you have a Actions Semi OWL based board and want to use the on-chip
+         serial port, say Y to this option. If unsure, say N.
+         Single baudrate is supported in current implementation (115200).
+

 config PXA_SERIAL
        bool "PXA serial port support"
        help
 config PXA_SERIAL
        bool "PXA serial port support"
        help